Jump to content
SAU Community

Official NSW Skyline spotted thread


CerealKiller

Recommended Posts

Crazy man! your near Mowbray. Probs walk straight past mine as well. Gunmetal R32 gtr on or there abouts and towards Station.

never noticed but honestly with the amount of attention i pay when I'm walking to the station i've probably past it every day :D

Drove past a white R33, sticker bombed front bar and orange wheels tonight on the Grand Parade near Brighton.. I'll assume it was Joel.....

lol unfortunately it was, not to many dickheads with orange wheels rolling around :P, went out for a coffee with the ms's and a few friends, was it parked up or was i driving? wasn't paying to much attention :(

Link to comment
Share on other sites

lol unfortunately it was, not to many dickheads with orange wheels rolling around :P, went out for a coffee with the ms's and a few friends, was it parked up or was i driving? wasn't paying to much attention :(

haha nah i think it looks good! you were turning right at a set of lights going away from brighton when i drove past going the other way thumbsup.gif

Link to comment
Share on other sites

Just saw a white R34 GTT with black wheels and Nismo sticker across the top part of the windshield outside Supercheap Auto in Mittagong. I was the guy with the blue jeans and hoody who came out of Supercheap and then went into Dick Smiths just so I could see who you are. :nyaanyaa: Car looks really clean too. :thumbsup: I was driving off in the red Hyundai Excel, I would've waved but I wasn't in my 34 and it would've looked retarded, lol. If you're on the forums, we should go for a cruise or something; seen you quite a few times.

And I also saw a white R33 with racing stickers on the front left quarter panel in the same parking.

Link to comment
Share on other sites

Cruised with a 32r along penno road and castle hill rd for a bit last night, plates were rb-26-?? or something along those lines...sounded nice,

also saw a dark grey/black 4 door 32 with uber flared gaurds on Brisbane rd in castle hill gave a wave, nice wheels. thumbsup.gif

Link to comment
Share on other sites

Cruised with a 32r along penno road and castle hill rd for a bit last night, plates were rb-26-?? or something along those lines...sounded nice,

also saw a dark grey/black 4 door 32 with uber flared gaurds on Brisbane rd in castle hill gave a wave, nice wheels. thumbsup.gif

Was the plates black and silver or black and gold???? He's been hanging around the hils for ages

Link to comment
Share on other sites

Just saw a white R34 GTT with black wheels and Nismo sticker across the top part of the windshield outside Supercheap Auto in Mittagong. I was the guy with the blue jeans and hoody who came out of Supercheap and then went into Dick Smiths just so I could see who you are. :nyaanyaa: Car looks really clean too. :thumbsup: I was driving off in the red Hyundai Excel, I would've waved but I wasn't in my 34 and it would've looked retarded, lol. If you're on the forums, we should go for a cruise or something; seen you quite a few times.

And I also saw a white R33 with racing stickers on the front left quarter panel in the same parking.

I see this guy quite a bit. And there is a White R32 GTS-T/4 (didn't get a good look) in the Highlands too.

Link to comment
Share on other sites

I see this guy quite a bit. And there is a White R32 GTS-T/4 (didn't get a good look) in the Highlands too.

Yeah, I've seen that white R32 quite a few times actually. Saw him just the other day as a matter of fact, haha.

Link to comment
Share on other sites

spotted a white r33 series two with a female blonde driver along pennant hills rd at like half past three i was in the blue s15 in front of you.... and then when getting petrol a white r34 gtt heading towards parramatta on pennant hills rd similar time.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...