Jump to content
SAU Community

Recommended Posts

haha yeh that was me... David's 21st birthday!

Kept my car there for the night cause I drank way too much - cousin got up the next morning and took her for a joy ride :P

Was parked behind a black 33 with SAU sticker last night around 11pm somewhere off Bligh St Guildford, im guessing we could have been at the same house party across the road? lol

haha yeh that was me... David's 21st birthday!

Kept my car there for the night cause I drank way too much - cousin got up the next morning and took her for a joy ride :P

Thats the one haha i was in the white 34, not sure if i parked before or after you arrived.

What a coincidence, iv always been on the lookout for another SAU car, didnt think i was gonna end up at a random party with one haha :D (i just met David lol but my gf went to school with him)

Thats the one haha i was in the white 34, not sure if i parked before or after you arrived.

What a coincidence, iv always been on the lookout for another SAU car, didnt think i was gonna end up at a random party with one haha :D (i just met David lol but my gf went to school with him)

Haha what a coincidence - I got there after you cause I remember talking about your car with my misses - it looked awesome! ;)

Thats the one haha i was in the white 34, not sure if i parked before or after you arrived.

What a coincidence, iv always been on the lookout for another SAU car, didnt think i was gonna end up at a random party with one haha :D (i just met David lol but my gf went to school with him)

Haha what a coincidence - I got there after you cause I remember talking about your car with my misses - it looked awesome! ;)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...