Jump to content
SAU Community

Second Hand Tyres - Never Pay For New Tyres Again.

V-Spec

By V-Spec,
in Victoria

 Share

Recommended Posts

WARLORD BAS Collaborator

WARLORD BAS

Posted
Posted

HEKT1K - 2 reasons to be honest, 1 is because i want to lower the car abit more, 2 because 235 tyres are alot easier to come by as i work at vw.

hamish - haha funny you say that, as i work on burwood road close to tyrepower, im good mates with mickey, sami, loc. got my wheels from there also.

and about the legality issue, well my car has a high mount setup on it now, and the wheels stick out the guards (18x10 +22) so i think ill be screwed over for other stuff anyway. (no this doesnt mean that i dont care about any law lol)

V-Spec Rising Star

V-Spec

Posted
  • Author
Posted
HEKT1K - 2 reasons to be honest, 1 is because i want to lower the car abit more, 2 because 235 tyres are alot easier to come by as i work at vw.

hamish - haha funny you say that, as i work on burwood road close to tyrepower, im good mates with mickey, sami, loc. got my wheels from there also.

and about the legality issue, well my car has a high mount setup on it now, and the wheels stick out the guards (18x10 +22) so i think ill be screwed over for other stuff anyway. (no this doesnt mean that i dont care about any law lol)

which vw, camberwell?

femno Grand Master

femno

Posted
Posted

But hang on, you guys arent mentioning anything about PROFILES, when that is the second most important thing when stretching tyres...

Bas, the guys at T.P Hawthorn chucked on some 225/45s on my 9.5 rims fairly easily, took them a few goes but they got them on, 235s wouldnt be a drama on a 10 as long as you use 45 profile. They have the equipment down there to blow the tyre onto the bead.

I want to try a set of 215/45 on the 9.5 next time lol.

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

i can see the benefit for a roady maybe, but i just booked in for Traction Tyres to fit/balance a set of Kumho KU36's, 245/40/18, $1k. Fair bit less if i wanted to stretch some 235's on (much more common size) but they said for a 18 x 9 rim, with track work, no less than 245. So that's what i did

although, if i was JUST driving on the street, i probably would consider some second hand ones. But Ash is spot on though, if they've seen quite a few heat cycles, the tread could be great but the compound has just gone to shit (a bit like my $$ bridgestones are now) and makes the tyres worse than a set of Lin Longs or something

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card stile AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had not flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • tsuokun
      Lets play a game - What is causing my oil consumption?

      By tsuokun · Posted

      Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
    • Shoota_77
      Car Rotisserie

      By Shoota_77 · Posted

      Hi guys, has anyone either purchased or built themselves a rotisserie for their car before? I can only just justify the need for one hence why I should just make one but at the same time, if I make one I can kiss another 4 weeks of potentially productive car working time goodbye because I'm building a bloody rotisserie....  I mainly want it for the application of the body deadener.  Cleaning the old stuff off, priming and then colour over the deadener doesn't worry me, it's just the application using the Schutz Gun that I feel would achieve a significantly better finish painting it side on and keeping the Schutz Gun upright.  I don't think they would work well on the side let alone almost upside down for some areas.  If the product I use (Terosun, etc) could work through a HVLP ok then it might be ok to apply without the rotisserie.   I can get one of these style ones for about $1200 which is pretty good value-     I reckon if I made one it would cost around $500 but it's more the time that it would take is more of a killer than the cost.  They look to hold their value pretty well second hand so I could always sell it after using it and realistically only lose $200-$300 at worst.  Or keep it and buy another project when this one finally sees the light of day... Anyone selling one...? Cheers!  
×
×
  • Create New...