Jump to content
SAU Community

R34 Gt Ignition Problem

durty 4

By durty 4,
in Engines & Forced Induction

 Share

Recommended Posts

durty 4 Rookie

durty 4

Posted
Posted

Hey all,

New to the forum but have been a long time lurker.

Have been faced with a strange problem on my 1999 R34 GT. Sometimes when ive been starting the car the MIL (engine check light) comes on and the car tends to shake a bit more than normal, noticing this i realised that it runs on 5 cylinders instead of 6 when it lights up. :)

However the light will only light up once or twice a week and the car runs fine (all 6 cylinders working) whenever I happen to start the car and the light does not show up.

I managed to get the ECU scanned recently when it lit up and the error code 21: Ignition Signal Circut came up.

Is it likely that this is due to a faulty coilpack or related to the crank angle sensor?

Has anyone else had a problem similar to this?

cheers

matt

Link to comment
https://www.sau.com.au/forums/topic/292294-r34-gt-ignition-problem/
Share on other sites
666DAN Grand Master

666DAN

Posted
Posted

Most common R34 problem in the world, replace the coil packs as they all die eventually and you'll be running on less and less cylinders until it won't go.

I don't know of a single R34 that has not had this issue.

James Kelsey Newbie

James Kelsey

Posted
Posted

Just a word on this: I went a cheapo route and just bought one new Nissan coilpack before I learned about those coilpacks and regretted it. I ended up having to go back and buy a full set of 6 Splitfires. Haven't had a problem since... and now I'm having the same problem on the "new" 25GTt I just bought - need to go tomorrow and buy another set. :cry:

skylinelova07 Contributor

skylinelova07

Posted
Posted

Hey matt, I had this problem when I was helping my brother switch engines in his Datsun 1600. We were running on 3 cylinders instead of four. This was due to both electrical problems but we also found out that we had a couple of vacuum leaks which of course does not allow enough pressure for the pistons to work properly. However, from the sounds of things, it seems that your problem may be electrical (coils).

Good Luck with it.

Luke.

R34 -_- Community Regular

R34 -_-

Posted
Posted

iv replaced all my coils about 8,000ks ago and now im getting a missfire in the low rev range while cruising, but the check light DOESN'T come on like it did with the faulty coils. spark plugs maybe?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • GTSBoy
      Finding E-30 & E-85 in Sydney

      By GTSBoy · Posted

      This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
    • Duncan
      Finding E-30 & E-85 in Sydney

      By Duncan · Posted

      Sorry, I wasn't very clear.....just that the standard injectors are apparently good over 600rwhp/450rwkw which you won't get to on standard turbos anyway.....they are much better sized from factory than we are used to in RBs.
    • PranK
      Finding E-30 & E-85 in Sydney

      By PranK · Posted

      I'm not sure where you are, but United Terrey Hills has E85. 
×
×
  • Create New...