Jump to content
SAU Community

Recommended Posts

Alright, i am having a few issues with my car and i've tried a few things but still haven't fixed it.

Stats:

rb20det power silvia. rb25 tubo, stock exhaust, hks mushroom pod, malpassi rising rate fuel reg, vl turbo fuel pump, injectors flushed and flow tested spot on last week. EL falcon o2 sensor mated to skyline plug, rb20det wastegate stock boost (around 8psi), afm cleaned regularly.

Problem: when my car is at idle it misses and the revs drop a little. This is intermittent (spelling?). Also, when on the gas peddle and if i back off, then accelerate again sometimes there is a big miss and it's a little hard to start in the morning. Overall, my car doesn't perform as good as what i think it should. Uses about 350 klms to a tank.:headspin:

This problem has been around for a while so i got the injectors flushed and flow tested. They were spot on, i recently put a fuel reg in and set it at 40psi, now the car is a bit easier to start but is still a pain. NB, i didn't remove the stock fuel reg.

Does anybody have any suggestions for this at all?? It's driving me crazy. :blast: Im going to remove the coil packs and give them a clean shortly.

Any ideas, comments and suggestions are greatly appreciated

Thanks :)

Jayson

Link to comment
https://www.sau.com.au/forums/topic/29241-problem-diagnostics/
Share on other sites

cleaned the aac valve yesterday. That's the thing mounted on the back of the manifold right with the cylinder like contraption bolted onto it?

Fuel pump was new about 4 months ago when i did the conversion. Plug gap is about 0.8 i think. bcp6res are the plugs im running im pretty sure. I'll double check the bov for leaks i think.

Thanks people

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • lol no cats running str pipes … might put the high flow back on but I suspect it might effect my ignition timing a bit. 
    • That looks a bit like yellowing to me. If the rear bar was looking like that from rich idle, I'd ask the question, do you have a catalytic converter fitted, and fully working?
    • Oh yeah gets really bad down here. I’ll have to upgrade the heater and wind screen wipers as well for optimal performance.
×
×
  • Create New...