Jump to content
SAU Community

Recommended Posts

Hey guys,

I just got my car dyno tuned by Gavin Woods, he's an absolute champion.

Car is currently putting out 315hp at 0.9 bar.

Specs are:

1993 RB25DET

Apexi PowerFC

Bosch 040 Pump, Tomei Fuel Reg, Stock Injectors

KKR560 Turbo, front mount, stock AFM, Greddy Profec B Spec II

He said he could only run 0.9 bar of boost as the AFM was maxxed out, and injectors were at 92% and he doesn't like going above 90%

So... I'm gonna save up for injectors and an afm, and had a few questions....

1) What injectors and AFM would you recommend? I'm not planning on eventually running any crazy power, just wanting to fix whatever's "holding back" the engine :D

2) how much boost would you run on a stock engine? (140,000km) The turbo seems as though it would be happy to run 20psi+ but i'm guessing the engine wouldn't last

3) Are there any other bits I would need or should get? EG: will new afm need an adapter for the existing pod filter or wiring in a new loom, or any other bits that should be changed at the same time?

4) Where should i get these bits from?

Thanks guys :P

Isaac

Edited by islade

i pretty much have the perfect information on injectors atm in my post just below yours :D

and the afm is covered heaps here already, get a z32 afm.

and for how much boost, lol thats covered alot to..

ive learnt to use the search bar since my first post otherwise u look like a complete tool.

Edited by Stealthynsa

1. Z32, Nismo 555's

2. Who knows, more about the tune than anything.

3/4. Nengun, greenline, any of the forum traders as well. AFM will be larger, might need a new adapter.

Nasty turbo though the 560 :D

Also, once you put in larger injectors, put the factory fuel reg back on, you do not need the Tomei one.

Thanks for the advice guys,

I have read either 440cc or 480cc for S15 injectors, guess I gotta do more research :banana:

What's the reason for returning to stock FPR if i get bigger injectors? I realise I may not need the additional pressure, but can't it just be turned back down?

Isaac

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
×
×
  • Create New...