Jump to content
SAU Community

Recommended Posts

Hey how u going guys I'm new to this site. I just bought an R32 Skyline from Melbourne n drove it to Adelaide. It's still registered for 6 months with Victorian rego. I went to rgister it and transfer it into my name but I couldn't get it registered cuz they couldn't find a compliance plate so I got told they'll mail something out and then I need to go to Regency for a full Inspection. Any advice ?

Link to comment
https://www.sau.com.au/forums/topic/293844-hello/
Share on other sites

If you have any rims, coilovers, overly load exhausts/decats, shit non-ADR compliant steering wheel, gauges everywhere boost controllers, turbo timers - Will all need to be changed to avoid a full regency inspection.

Link to comment
https://www.sau.com.au/forums/topic/293844-hello/#findComment-4904115
Share on other sites

Welcome mate.

If it was complied in VIC prior to your purchase, it should only require a VIN & ENG No check.....can be done at Lonsdale.

are they strict at lonsdale? i know they are pretty strict at regency... just wanted to know lol

Link to comment
https://www.sau.com.au/forums/topic/293844-hello/#findComment-4905834
Share on other sites

It wouldn't happen to be an 88 or 89 model would it?

If that's your car in as your avatar picture i'm pretty sure that i can see your compliance plate in Blue. (UNless the factory skyline plates are blue, the s-series ones aren't)

If it is an 88 or 89 model than it'd be complied under the 20 year rule and doesn't need an Australian compliance plate just the factory one.

Link to comment
https://www.sau.com.au/forums/topic/293844-hello/#findComment-4906439
Share on other sites

It wouldn't happen to be an 88 or 89 model would it?

If that's your car in as your avatar picture i'm pretty sure that i can see your compliance plate in Blue. (UNless the factory skyline plates are blue, the s-series ones aren't)

If it is an 88 or 89 model than it'd be complied under the 20 year rule and doesn't need an Australian compliance plate just the factory one.

Just to clarify, no compliance plate (i.e. it came in under the 15 year rule) means a full pit inspection at Regency, regardless of whether it has been registered interstate before.

Link to comment
https://www.sau.com.au/forums/topic/293844-hello/#findComment-4906846
Share on other sites

Please use the search function - this has been covered dozens of time before.

And if you desperately need to make a new thread (for some reason), please be VERY descriptive as to what your thread is about - "Hello" is completely unsatisfactory. Something like "Buying a car from interstate, help needed" would have been much more appropriate.

Link to comment
https://www.sau.com.au/forums/topic/293844-hello/#findComment-4909901
Share on other sites

Please use the search function - this has been covered dozens of time before.

And if you desperately need to make a new thread (for some reason), please be VERY descriptive as to what your thread is about - "Hello" is completely unsatisfactory. Something like "Buying a car from interstate, help needed" would have been much more appropriate.

no prob mate
Link to comment
https://www.sau.com.au/forums/topic/293844-hello/#findComment-4909911
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...