Jump to content
SAU Community

Recommended Posts

Ok as most as most of you guys know recently i had to change my Lower Control Arm and Caster Rod, after getting a new set of tires, alignment and suspension check the car is starting to pull to the left (if I let go of the steering wheel it will just start going to the left) I was wondering what you guys think it is, it drives fine i took it to the midnight cruise with no dramas but its worrying me for the Buller cruise. Does anyone know of a good suspension specialist near Caulfield East? After a close examination I think I've tightened the LCA bolt too tight but it seems to be stuck now (It free spins, no amount of untightening or tightening makes it move) I'm currently getting another bolt from the guy I bought the LCA from but I just haven't had the time (as he lives in Frankston) although I dont think it will have a major influence on the steering will it?

Any input appreciated

EDIT: I have to keep the steering wheel slightly to the right for it to go straight

Link to comment
https://www.sau.com.au/forums/topic/294690-car-pulling-to-left/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Ok as most as most of you guys know recently i had to change my Lower Control Arm and Caster Rod, after getting a new set of tires, alignment and suspension check the car is starting to pull to the left (if I let go of the steering wheel it will just start going to the left) I was wondering what you guys think it is, it drives fine i took it to the midnight cruise with no dramas but its worrying me for the Buller cruise. Does anyone know of a good suspension specialist near Caulfield East? After a close examination I think I've tightened the LCA bolt too tight but it seems to be stuck now (It free spins, no amount of untightening or tightening makes it move) I'm currently getting another bolt from the guy I bought the LCA from but I just haven't had the time (as he lives in Frankston) although I dont think it will have a major influence on the steering will it?

Any input appreciated

EDIT: I have to keep the steering wheel slightly to the right for it to go straight

Maybe they didn't align it probably? Because if problems was with the things you install, wouldn't the car sway left when the steering wheel is straight? It's just a guess lol

But I'd hate to see you fall off the mountain next weekend :down:

its meant to veer to the left ever so slightly if you take your hands off the wheel

its a safety feature designed to make you not run onto the wrong side of the rd

just check how much - if in doubt goto a wheel balance / suspension place

Could it potentially be your tie rods? Even after an alignment, the settings won't stick if your tie rods are porked.

Suggest you get those looked at.

A nice place to go around East Caulfield; perhaps Pro Tek tyres? They're located on the corner of Ferntree Gully Rd and Dandenong rd. If not there, you can head down Nepean Hwy towards Nissan Brighton. Theres a place directly across from there but I'm not sure of the places name.

Good luck.

its meant to veer to the left ever so slightly if you take your hands off the wheel

its a safety feature designed to make you not run onto the wrong side of the rd

just check how much - if in doubt goto a wheel balance / suspension place

Actually, thats true. Because the roads are made to be on an angle, so water and stuff rolls off to the side. There's one way to test it, is to drive in the middle of the road (of course when there's no cars), then let go off the steering wheel lol.

Could it potentially be your tie rods? Even after an alignment, the settings won't stick if your tie rods are porked.

Suggest you get those looked at.

A nice place to go around East Caulfield; perhaps Pro Tek tyres? They're located on the corner of Ferntree Gully Rd and Dandenong rd. If not there, you can head down Nepean Hwy towards Nissan Brighton. Theres a place directly across from there but I'm not sure of the places name.

Good luck.

ProTek and tierods/ends.... sounds like a plan.

Will pull to the left on most roads due to the slope, if you run a little more castor on the left i think it is it drives straight on cambered roads.

also take into consideration tyre condition and inflation, make sure they are all even,

and possibly brakes dragging or handbrake being overadjusted on the left side

or even a dodgy wheel alignment, these 4wsteer systems need experienced ppl to do them right.

could be a stuffed Tie rod since you hit it hard enough to bend an LCA

did you get an alignment print out from the aligner,

as some places will just say, we made it as straight as we can, without showing any printouts with all the alignment settings

could be a stuffed Tie rod since you hit it hard enough to bend an LCA

did you get an alignment print out from the aligner,

as some places will just say, we made it as straight as we can, without showing any printouts with all the alignment settings

Yea man Nathan gave me the alignment print out but I dont know about this stuff, I'll go get it and post it up here to see if anyone know about it

Some comments the mechanic left after a comprehensive check:

Play in L/H Front King Pin

Play in L/H rear tie rod end and upper control arm joint

L/H ball joint rubber cover split

sounds pretty serious..........

2deg less castor on the left than right, 2mm less toe on left than right, 1deg less neg camber on the left. Normally when they can't adjust camber and castor atleast get the toe equal side to side... Take it somewhere that can give advice when they see the camber/castor is out that much with no adjustment IMO.

i see this as the issue. the .3 of a degree difference in camber on the rear is insignificant compared to the fronts overall differences.

yeah i agree with ryan,

all you have to do is just look at the final values column and compare left to right

The values should be very similar left to right

your front end is showing some major differences

take it to a suspension specialist and see if they can fix it using factory adjustments

otherwise, the problem lies deeper within the suspension mounting points which could have been damaged in the accident, or possibly a bent hub

Are you running standard (stock) suspension setup?

If you are - try to find the factory manual - it seems to have all the correct angles (specs) etc. and send it to the wheel/suspension place.

Then take the car for a run on the freeway.

Ok well the story is that I brought the car to ProTek where they said (after looking at the alignment sheet) that he thinks the guy wasn't exactly the most capable but in his defense he said that he thinks the whole suspension has been pushed back and in a bit, his suggestion was to bring it to pedders and get an aftermarket setup that would allow me to adjust and compensate for the damage, or to bring it to a specialist and see what they can do. He recommended me to Kents but of course every time I hear "panel beater" there is only one real name that comes to mind when operating on a budget (Vu) so the car is now with Vu @ DT Panels and hopefully he'll be able to get it fixed with no real dramas and at a good price

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well.... it's not just "de-oxygenating". If you do that you just have, most likely, ethane. So you still need to do a synthesis step to combine a number of ethanes/ethanols to make circa-8-chain hydrocarbons. And of course you don't want straight chain HCs, because n-octane actually has a negative octane rating (ie, it's worse even than the n-heptane which sets the zero on the octane scale!), so you have to do some tricky catalytic chemistry to synthesise branched HCs. That's all doable - but it doesn't come for free. And.... it starts with ethanol, which is an agricultural product, and there will almost certainly never be enough of that as a base stock to replace the liquid fuels that are in use. You really wouldn't want to be planning to be using any more ethanol for fuels than is currently already used (in E10, E85s, etc). And ideally you'd be looking to reduce such usage, as it is largely wasteful, particularly in the stupid-ole'US-of-A where the corn lobby has organised it so that it's actually primary production corn that is used to make a lot of the ethanol, not by-products and waste, like it is (mostly) elsewhere. So, what I said about needing free-ish energy probably still applies. True synth fuels would be made from H2 and CO2, in a near reversal of the combustion process. In fact, given that the H2 would be split from water first, it actually is a complete reversal of the combustion process. But...energy intensive. The human race burns something like 1 cubic MILE of crude oil, after it has been made into various fuels. Every year. That's a simply stupendous amount of energy. Just assume that the density is 900 kg/m3, and that the calorific value is 45 MJ/kg, then that is 165.9 x10^12 MJ of energy. Or more than 10^19 Joules. You get a maximum of 1 kJ/s per square meter solar radiation falling on the planet's surface, and so if you halve that for daylight, and halve it again for average weather (highly optimistic) and then take ~25% for the very best efficiency of solar panels, then you need about 85.7 billion square metres of solar panels to generate enough electricity to replace that liquid fuel energy consumption. Each panel is about 1m2. That's a rather large number of panels. We also burn about a cubic mile of coal. We also use hydroelectric power. We also use nuclear. We also use a number of other sources, both "renewable" and not. You can kind of ignore the renewable ones (except for hydro, because it will all end up getting subsumed into pumped hydro for storing other renewables, and so it won't be the standalone renewable that it originally was), so we end up needing a multiple of the ground area number that I just arrived at.
    • Corvette thread then? Don't say I didn't predict the future again. "I love the little MX5, I do, but I just want something a little easier to get in/out of, a little more cushy and some power would be nice - I miss the V8 Rumble... I found this clean red C5 for sale recently and..." I'll do you a great deal on the next step, which is one of those but you can fit people in it, too.
    • What about renewable diesel and/or gasoline? I see some projects spinning up like de-oxygenating ethanol to make drop-in compatible bio-gasoline especially in CA. I still think the future is EVs and we should've all gone full throttle on nuclear power after the 1973 oil crisis like France. Despite 15 years of work in CA to reduce the CO2 intensity of generation with renewables our electric grid is still far worse than even "low carbon" nuclear power. ICE is pretty cool when you aren't depending on the stupid thing to be practical and reliable and cheap as possible to get you to work every day. It's kind of like mechanical watches or vacuum tube amps.
    • I just rolled over "my" first 10k km in the MX5 Every time I go anywhere it always ends up in a adventure to look at houses and find some random country roads I've been on leave since early November but unfortunately need to go back to work on 19 January Luckily though I still have a fair chunk of leave left to burn until.... Not that I'm counting 😁
    • These look like S13 wheels.  And Welcome! 
×
×
  • Create New...