Jump to content
SAU Community

S15 Rb26 R33 R32 Rb20 Rb25 Parts Galore Also Misc Parts

toy515
 Share

Recommended Posts

toy515 Grand Master

toy515

Posted
Posted

S15 PARTS

s15 camber arms $20

s15 rear parcel shelf $40

s15 genuine veilside rear bar make a offer i need it gone

s15 adm passenger sunvisor $10

s15 washer bottle $10

s15 overflow bottle $10

s15 eyelids paint black with glitter $50

s15 drivers side under dash bit $20

RB26 PARTS

r32 rb26 coilpacks $30 each

rb26 timing belt only 8000kms old genuine nissan $20

rb26 flywheel $30 will also fit rb20 rb25

r32 rb26 dump pipes with 02 sensors $50 pair

rb26 baffle plates (bolt to bottom of engine) $30

rb26 alloy engine brackets $30

R33 GTST PARTS

r33 gtst gearbox crossmember will fit r32 r33 s13 s14 s15 $20

r33 gtst manual brake pedal $20

r33 gtst manual clutch pedal $20

r33 rb25 rear tailshaft $30

r33 radiator brackets $5

rb25 rb20 rb26 starter motor low kms $30

R32 GTST PARTS

r32 gtst manual brake pedal $20

r32 gtst boot seal $30

r32 under dash drivers panel $15

rb20 cam gear cover $20

r32 washer bottle $10

r32 overflow bottle $10

r32 drivers side electric window thingy $15

MISC

drift 3 inch stainless air filter $20

4 inch canon $20

5 inch canon $40

boost tee $10

kenwood 4 channel amp $70

LOCATED ON THE GOLD COAST BUT WILL POST.

BRAD 0421511710

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      Skyline r34 gtt tie rod

      By drifter17a · Posted

      does anyone know tie rod torque setting and anti roll bar for r34? Is there a workshop which shows various components torque setting?
    • drifter17a
      Eibach wheel spacer

      By drifter17a · Posted

      Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • GTSBoy
      Disposing of shocks/struts?

      By GTSBoy · Posted

      Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • PranK
      Disposing of shocks/struts?

      By PranK · Posted

      It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
×
×
  • Create New...