Jump to content
SAU Community

Recommended Posts

yup.

how would going to a cooler plug help? When I swaped to iridium, the old plugs were coloured perfectly, not indicating detonation or other nasties (had light tan colour, no damage to tip or ceramic etc)

please advise...

irridium / platinum + boost = :P

i replace about 10 sets a week.

hmm. Fair enough. Lol

but it had ngk coppers in it before I change coilpacks n plugs. I only changed to iridium and splitfires BECAUSE of this problem. That's why I'm kinda thinking it's not an iridium problem, as it did it with the coppers.

So what else could it be?

hmm. Fair enough. Lol

but it had ngk coppers in it before I change coilpacks n plugs. I only changed to iridium and splitfires BECAUSE of this problem. That's why I'm kinda thinking it's not an iridium problem, as it did it with the coppers.

So what else could it be?

however correct me if I'm wrong, you've obviously got alot more know how than myself, I'm just confused cos it originaly had coppers when this problem started :P

were the coppers gapped properly?

umm. One would assume so. Honestly. I can't know for sure. They were put in when I needed a new coilpack a while back. The boys down at HPF/Amberly Auto did it. They usualy are pretty on the ball down there.

However who knows. What u recommend the gap be at? These iridiums are .8 and cos the coppers where the same heat range I assumed they where .8 too.

.8 is the standard...

does it ever clear up after a long drive?

at times I feel that it is worse when cold. Esspecialy those first realy yucky severe kinda ones at lower rpm. That's always heaps worse when cold. And eases off (doesn't stop though) after driving for a fair time. but as for the higher rpm one. That severity remains the same no matter how long I've been driving for. But as mentioned in first post, it may (rarely) not

even occur, it won't do it maybe every 3rd attempt. And when it DOESNT occur, I don't know if this is in my head, but the power feels a bit lacking.

could be your plugs fouling and clearing up on long drives...

bung o2 sensor making it too rich, especially on cold start perhaps?

old plugs showed no signs of fouling, as far as I could tell with regards to coloration and wear. Plus now the plugs are new (however possibly have the iridium + boost = :P dillema)

is there a way to isolate the o2 sensor as a possible culprit? Or in my case, actualy locate it!

Thanks for u help so late :) (if I dont reply any more it means my brain went into

a sleep deprived coma, to Wich I'll respond asap in the morn)

Mate, based on your description, I had the exact same problem.

You tried to accelerate quickly and it bogs, hesitates and jerks. Difference with mine was it wouldn't push through unless you lifted off the throttle some.

I unplugged my O2 sensor and the symptoms would ease up/disappear but then, without the O2 sensor I got shit fuel economy. Tried a new O2 sensor but that didn't fix it.

I did heaps of things, cleaned the AFM, resoldered connections, new copper plugs, changed the gap to 0.7mm, swapped all of my coilpacks/loom/ignitor with known working items from a mates car.

The problem remained until one day I removed my front mount/pipes and replaced it with a large sidemount. My deduction is that there was an air leak on the inlet piping (which isn't surprising considering I had welded my own pipes and I didn't pressure test them).

Makes sense that the more boost you run the worse it gets. Get a PVC pipe end cap, screw a tyre valve into it, install it in place of your AFM and pressurise your inlet piping, this should identify any leaks pretty quickly.

Mate, based on your description, I had the exact same problem.

You tried to accelerate quickly and it bogs, hesitates and jerks. Difference with mine was it wouldn't push through unless you lifted off the throttle some.

I unplugged my O2 sensor and the symptoms would ease up/disappear but then, without the O2 sensor I got shit fuel economy. Tried a new O2 sensor but that didn't fix it.

I did heaps of things, cleaned the AFM, resoldered connections, new copper plugs, changed the gap to 0.7mm, swapped all of my coilpacks/loom/ignitor with known working items from a mates car.

The problem remained until one day I removed my front mount/pipes and replaced it with a large sidemount. My deduction is that there was an air leak on the inlet piping (which isn't surprising considering I had welded my own pipes and I didn't pressure test them).

Makes sense that the more boost you run the worse it gets. Get a PVC pipe end cap, screw a tyre valve into it, install it in place of your AFM and pressurise your inlet piping, this should identify any leaks pretty quickly.

wow. Thanx for your reply. I'll DEFINATELy add pressure test system to my list of things to do. Thanx heaps.

I'll let u know how it goes!!

Thanx again. Tys

  • 1 year later...

Ok big delay.

thought id add some closure to this topic for anyone who wants to know what the poblem was.

turned out to be a stuffed AFM.

Boys at AVO sorted it out for me, they had a spare AFM to test. was flawless from word go.

Ended up removing AFM and going MAP sensor and ECU lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • H2 (for cars) will never happen. It's not reasonable for any number of reasons. It's also not reasonable for almost all of the industrial uses that the fanbois say that it will be used for, again for a large number of reasons. There are some cases where it will be good. But, even those will be massively hampered by the economics. The only way that H2 can be economic is if we somehow manage to get from where we are to the other side of the economic-valley-of-death in which no-one can operate. You need there to be sufficient renewable generated electricity to be available so that it is effectively free. Once you are there, you can do whatever the hell you want and hang the efficiency. But until you get there, the ever diminishing value of electricity makes it harder and harder to encourage businesses to build the new generation capacity, and they will simply stop investing in generation projects. (I kinda think there needs to be just government money spent on building the required capacity in a non-commercial way, similar to how the first fossil fueled grids were built, as national-government owned utilities. And probably some nuclear in there to start. But this all should have started 10-15 years ago to avoid the chasm of death that we face right now). Synth fuels will be much more likely, but will only occur is there is at least some renewable H2 production, because you need H2 to do it. And you need stacks of free (or at least extraordinarily cheap) energy because assembling molecules back into fuels is exactly the opposite process to burning the fuel, and the reason we burn fuels is because there is so much energy squeezed into each molecule. So you're somewhat subject to the same economic valley of death problem as above anyway. That is unless people are willing to pay the current equivalent of $5 or $6 per litre of petrol-ish liquid fuels. Can you imagine it? The squealing at $2 now is bad enough.
    • This is so cool. Get a dashcam that records audio and hopefully you'll catch it.  Maybe there's a brand or some kind of markings on the back ? Are the pics hand drawn? I love it so much.
    • Hahaha yep, point(s) taken. I just like seeing different things and an EV in an R32 is pretty different. I'm not on the EV band wagon, I'm waiting for synthetic fuels or hydrogen personally. 
    • I mean it's probably likely that people overestimate their skills in dialling in a setup and noticing the changes. I had SK shocks and springs, and added heavier springs and got them revalved by Sydney Shocks to suit based upon what I told them I wanted the car to handle like. I got back a completely different feeling set of shocks, which probably (?) feel great on track but holy hell are they rough on tram tracks and the like. The shock dyno actually looks pretty similar to Shockworks (from what I can surmise from a screenshot of a youtube video - and my dyno printout...) Truth be told I doubt I'd be any faster or slower with either setup, or camber/castor combination. I also had whiteline eccentric castor bushes up front of my R34. I removed them and put in poly non-adjustable ones to soothe my OCD (nobody ever set the castor the same side to side, and it'd be near impossible to do) and be happy the wheel is centered in the well now for clearance reasons. Yes I wanted it to move 1mm 'back' :p I've effectively set my castor back to stock, negating all the benefits of that which is supposedly massive. I've probably also altered toe and camber in a negative (detrimental) way. I can't tell any difference steering the car.
×
×
  • Create New...