Jump to content
SAU Community

drifting japanese animation style


Recommended Posts

was watching cartoons this morning and i think i say an add for some animated drift action on dvd, has anyone else seen this or was i still asleep?? What i saw was an rx7, ae86 and a r32 gts-t all drifting??

i think it was called "inatial D" it was only a few seconds of it!

Link to comment
https://www.sau.com.au/forums/topic/29554-drifting-japanese-animation-style/
Share on other sites

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

yeah madman's released the 1st americanised initial D dvd in australia. We actually have a madman rep on the forums so if you need more info on the DVD you could ask him.

As for me, I like the oldschool jap version with subtitles :cheers:

I just bought the first Initial d dvd from autobarn. It has both the jap version and the american version on it. Apparently its going to come out on 10 DVDs or something, but you can only get the first 2 at the moment.

umm in the last 10 days I've got the entire 1st stage and am making my way thru the 2nd stage now from kazaa..no problems..

I've heard that the dubbed version is really lame but I've ordered it anyway! haha

I watched Initial D last year, very good.

I have the whole collection including all 17 OST's.

Initial D First Stage

Initial D Second Stage

Initial D Third Stage

Initial D Extra Stage

Initial D Battle Stage

^^ There the video stages, and an Extra that came out only on Jap Authentic DVD (There are many bootlegs.) The Initial D Super Euromach Special.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...