Jump to content
SAU Community

R33 Gtst Gearbox In A R31 Need Help Urgent

arabian_drifter
 Share

Recommended Posts

arabian_drifter Community Regular

arabian_drifter

Posted
Posted

hey peoples , i just bought a 33gtst gearbox to fit in my r31 skyline .

i found now while im under the car that the gearbox mounts and the tailshafts dont line up .

i have the r33 yolk and i have the standard tailshaft from my r31 gearbox , so i thought i can mix and match , but none of this combo seems 2 work .

can any1 tell me what exactly is needed for this ? do i need 2 get a differnt rear end of the tailshaft?

any help would be good

thanx

arabian_drifter Community Regular

arabian_drifter

Posted
  • Author
Posted
Alot of cutting and shutting I'm afraid, difficult conversion unless you're handy with the fabrication tools...

yea thanks 4 the tip .

got it all sorted .

the auto cross member went straight on .

and i used my standard manual tailshaft with the r33 yolk i had .

cutting and shutting he goes lol

Birds Grand Master

Birds

Posted
Posted

It's usually the way with a gearbox conversion, I apologise.

If it hadn't have worked would you have come back and said thanks? :banana:

Just be careful any difference in length or angle doesn't put added pressure on the output shaft seal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...