Jump to content
SAU Community

Sluggish In Low Revs

Mooney

By Mooney,
in Engines & Forced Induction

 Share

Recommended Posts

Goodwin Apprentice

Goodwin

Posted
Posted
Hey, i have a R32 with rb25 na. Seems to be sluggish in low revs, anything above 4000rpm and its good, what can i do can a different tune or anyone else experienced this and found a solution??

cheers

Welcome to Club N/A where no power off the line is just the beginning.

WYTSKY Veteran

WYTSKY

Posted
Posted

Do u have an aftermarket exhaust? if so, it may be too big and actually cause a lack of back pressure resulting in the car being extra sluggish in low revs until a higher velocity of exhaust gas flows out, where it would be better for it...

_bobo_ Mentor

_bobo_

Posted
Posted

oOoO rb20...even worst lol

shoulda atleast tried to get a rb25.

but yeah 2.5inches is max you should go on a n/a otherwise you'll end up loosing back pressure.

2.25-2.5 is optimal for best performance. with a decent muffler and have it made as straight as possible.

WESTWD Community Regular

WESTWD

Posted
Posted
is 2.5 inch exhaust system good for a na rb20de r32 gts?

on your car, i personally would of gone 2.25 as i think 2.5 is too big.

hahahhaah lol

no need to laugh at him man, he was just after some advice.

R34GTFOUR Mentor

R34GTFOUR

Posted
Posted
you could always give the CAS a good twist in the advanced direction. will make it pick up much quicker, but the engine won't last that long.

Premium fuel goes a long way, I've been running mine at full advance for years, not a problem. Even in the peak of summer, full load, doesn't even think about pinging.

Definitely give that CAS a little twist, free HP imo.

mad082 Grand Master

mad082

Posted
Posted

if you are able to run full advance without pinging (unless you are running c16) then i wouldn't be suprised if your timing belt is 1 tooth out. or you just don't know what pinging sounds like. but then again the ecu is probably knocking 15 degrees of timing out because it is hearing the knock, so you could probably back your timing off a bit and not lose any power.

iseekool Veteran

iseekool

Posted
Posted
wtf i have a rb25 in mine, i have full exhaust system 2.5" with hi flow cat. worked diff and gearbox. adjustable fuel reg and gay ass pod filter. was thinking about extractors and chip it and give it a more aggresive tune

Run a few tanks of 98 fuel.

Remove any excess weight (stuff in the boot) - I'm guilty of having too much stuff there :rolleyes:

Check your tire pressures.

Clean your throttle body - you will be surprised how dirty it gets.

Try putting the pod in an enclosure or go back to a stock airbox and panel filter. You could be getting too much heat on the intake side of things.

Also are you running fairly wide tires and/or air-con? This causes alot of drag (resistance).

R34 -_- Community Regular

R34 -_-

Posted
Posted (edited)

"Premium fuel goes a long way, I've been running mine at full advance for years, not a problem. Even in the peak of summer, full load, doesn't even think about pinging.

Definitely give that CAS a little twist, free HP imo."

how do you do that?

Edited by R34 -_-
mad082 Grand Master

mad082

Posted
Posted

the CAS is located on the front of the engine. it is a round thing with i think 3 bolts located at even intervals around the outside. each bolt will be in an ovalised slot allowing movement of the CAS.

this should only be done with a timing light and having locked the ecu into timing mode first. this way you can monitor how much you have altered the timing. if you go too far and get pinging/detonation/knock and don't realise it, it can result in engine damage. also make a mark on where the timing was before you started so you know how much you have moved it if you want to back it off a bit.

R34GTFOUR Mentor

R34GTFOUR

Posted
Posted
if you are able to run full advance without pinging (unless you are running c16) then i wouldn't be suprised if your timing belt is 1 tooth out. or you just don't know what pinging sounds like. but then again the ecu is probably knocking 15 degrees of timing out because it is hearing the knock, so you could probably back your timing off a bit and not lose any power.

The belt hasn't been changed so it's not a tooth out and my brothers r33 gts had his on full advance aswell for years (when it was na). I know what det sounds like, she ain't pinging. Also when the stock ecu hears det and takes out 15 degrees of timing all of a sudden its noticeable, which it definitely isnt doing.

Not suggesting every just go and smash timing as much timing into theirs as possible, but for mine and my brothers, full advance worked a treat.

Ultimategtr Proficient

Ultimategtr

Posted
Posted

You cant hear an engine pinging, unless its pinging REALLY bad. Every engine is different. If you were to play with the timing, then you really need it up on a dyno to make sure its not pinging at all.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • OakvilleGTR
      Turn signal wiring question

      By OakvilleGTR · Posted

      Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • sonicii
      Lower A arm Skyline v35

      By sonicii · Posted

      The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...