Jump to content
SAU Community

Recommended Posts

SELLING A MANUAL GEARBOX R32 GTR BEEN RECENTLY PULLED OFF. SORRY I DONT HV ANY PICTURES OF IT BUT IT COMES TOGETHER WITH THE GEAR STICK WITHOUT THE KNOB. SELLING ONLY THE GEARBOX IF U WANT THE CLUTHCH PLATE ITS SEPARATE. ITS AN UPGRADED CLUTCH PLATE NOT SURE OF WHAT BRAND. BUT WILLING TO LET IT GO FOR $500. THE PRICE FOR THE GEARBOX WOULD BE $2000 FIRM. CALL ME IF U HV ANY INQUIRIES. WILL NOT POST ONLY PICK UP. CAR HAS DONE ABOUT 130000 KMS REZA 0432415424.

HAVE HEAPS OTHER PARTS AS WELL, INCLUDING DRIVE SHAFTS, CROSS MEMBER, STARTER MOTOR, FUEL PUMP, FUEL TANK, STOCK SPOILER, BOOT, LEFT FENDER, BOTH DOORS, WINDOW MOTORS, AFTER MARTKET EXHAUST NOT SURE WHAT BRAND, BRAKES COMPONENTS, CLUTCH MASTER CYLINDER, BRAKE MASTER CYLINDER, BUCKET SEATS MINT CONDITION, STEERING WRECK WITHOUT RACK ENDS, 19 INCH RIMS WITH TYRES HAS A STRATCHES FROM THE ACCIDENT, TAIL SHAFT, DIFF, TIEN REAR SHOCKERS WITH SPRINGS.

IF U WANT FAST RESPONSE I WOULD ADVISE YOU TO CALL ME AS I DONT OFTEN GET THE CHANCE TO GO ONLINE.

FOR ALL THE ITEMS ABOVE, JUST MAKE AN OFFER. ANY OFFERS MIGHT BE CONSIDERED. JUST WANNA GET RID OF THESE ITEMS. BUT PLEASE MAKE REALISTIC OFFERS

post-36577-1258607669_thumb.jpg

post-36577-1258607724_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/296914-heap-of-r32-gtr-parts-for-sale-melb/
Share on other sites

Price on front drive shaft??? or just the rhs inner cv joint???...delivered sydney......

front drive shafts 120 each...delivering im really not sure how do i go about doing that..if u can suggest anything im willing to send the pair at buyers cost

Hey mate i'm 3 sensors.

The first one is the out side temp sensor ( located near the aircon fan )

The second is inside temp sensor located in the center console near the cig lighter.

The third is the sunload sensor which is located in the dash passenger side top near the windscreen.

How much for these sensors.

Oh and can you confirm if your aircon was working

ahha nothing..i just dont know what they go for...i assumed it was much more as the r33 gtst was around 1k

r33 gtst ones can handle more power. harder to come by as more everyone wants them... going rate for r32 gtr is around 5-600$

  • 2 weeks later...

Hey mate

im after the rubber spacer that goes under the gtr wing on the outside drivers side.

Not the one that gets bolted down but the outside one.

Can pick up.

If you have it how much do you want?

Need it bad

Cheers mate

  • 7 months later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...