Jump to content
SAU Community

Recommended Posts

hi guys im having a poblem with my S2 attessa 4wd system ,

i have just fitted 2 second hand tyres one on the front pass and

the other on the drivers rear . both tyres have 50% tread and

all 4 tyres are the same size 245/35/19 . now when i drive the car

the 4wd system is coming on under normal driving conditions

front torque gauge reads anywere between 5 kg/m - 10 kg/m

and the car feels as if it is surging . im thinking that maybe because

the tyres are actualy slightly a diffrent rolling dia so therefore the

attessa system sensors are telling it that one of the wheels are spinning

enough to engage the 4wd . im just wondering if anyone has come across

this problem before ??????, there was nothing wrong at all with the car

before the 2 tyres were fitted , and no one touched the car at all while the

tyres were fitted and the guys who fitted didnt break or damage anything

because i watched him like a hawk like i do with anyone who works on my stag

HAHAHA :D;):wacko::D any help will be very much apprciated thanks guys and girls ....

Link to comment
https://www.sau.com.au/forums/topic/297204-s2-4wd-problem/
Share on other sites

Dude the diff rolling diameter is defs the prob. As a side not I noticed that the 4wd was kicking in more ofter with just lower tyre pressure (I know of others that this has happened to).

Also as kidafa said dont mix n match tyres from side to side on each axle. Not just for safety reasons but u can damage diffs etc by putting diff size tyres on the one axle.

Link to comment
https://www.sau.com.au/forums/topic/297204-s2-4wd-problem/#findComment-4950184
Share on other sites

And risk damage to the 4wd system? Good advice!

plesae tell me how it is going to damage it ? the rear wheels wont be turning faster than the front so it wont send any drive to the front . and the overall difference wont be any greater than the difference between wheel speeds when driving around a corner. i put the space saver on the rear of mine and it was a flamin mongrel . sent like ten% to the front . unplugged the green wire and it was happy as

Link to comment
https://www.sau.com.au/forums/topic/297204-s2-4wd-problem/#findComment-4951837
Share on other sites

thanks guys fo your help in conferming what i thought was the problem. i have changed the tyre that was the problem and it has fixed it . but i have booked the car in for 4 new tyres next week so my problem is now ALL GOOD thanks again eveyone who helped out !!!!

Link to comment
https://www.sau.com.au/forums/topic/297204-s2-4wd-problem/#findComment-4956136
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ayooo, been a while mates. I have a s2 r33 gtst and air stopped coming out of all the top vents.   My car has always made an actuator gear noise when turning the car on but that's a different issue I think? Did searches and am at process of thinking it's an actuator or some type of motor? I see a few different actuators and don't know which one. Would be nice to know if it was the one that's under the steering wheel so the dash doesn't need to come out.
    • Hi, just checking. Did you get this stuff made by Vspec Performance and at what price roughly? Looking into (sometime later) also getting such a intake kit, and Trust as well as HKS don't make a full set like this anymore.
    • 2025 Update PRP RB30 Black and Crank Shipped from Austrailia made it and was sent off to the machine shop. -700 to 800hp Service was done to the Block, which included: Inspection Prep and Black Brace to convert engine to 4wd oil Pan  Crank Fully prepped for 1000hp PRP RB30 timing belt kit w/ ALL options Nitto Pistons Nitto I-Beam Rods Nitto Oil Pump New OEM Nissan RB26 Cylinder Head Shipped Supertech intake and exhaust Valves over-sized Kelford 272 cams Mild Lift Nitto Headgasket All of the machine work is completed and next step is assembly and dropping in the new motor.   Upgrades (Changes) from the previous build: Engine Management - no longer using ECUMasters. Haltech Platinum Pro Turbo - Went from twin HKS 2530s with upgraded wheels to BW362SX-E Fuel - 1000cc injectors to ID1430x Single in tank Walbro 450 to Radium External Surge Tank w/ 2x Walbro 450s     I am looking to be back on the road by the end of summer. Wish me luck! monthly updates should be coming!    
    • Realised I never posted this , also I never got a price 
    • I'm glad to hear you've joined the SKI club. Spend the Kids Inheritance.
×
×
  • Create New...