Jump to content
SAU Community

Recommended Posts

Just wondering if anyone has any thoughts or tried having their sub woofer behind drivers seat floor rather than in them boot. Is there much gain/less boot rattle you reckon?

Reason i ask is, i hate having a big sub woofer in the boot because it leaves to no room for spare tires

Link to comment
https://www.sau.com.au/forums/topic/297633-sound-system-location/
Share on other sites

given that a bass wave is rather long (in some cases 30ft!) and you have it right behind you - are you going to get 'best effect' vs having it far away as possible (IE boot.) ?

that wave needs to expand to really be felt/heard.

Boot facing in works well IF you seal of the box properly. Otherwise you get bass cancellation. I think thats the right word for it... basically the primary and secondary waves cancel each other out, which is why it generally sounds better that way when the boot is open.

The Crossfire Car Audio site used to have a good technical reference that explains the different subwoofer set ups for different types of woofers. (eg. band pass, isobaric, free air, sealed, ported, and some more elaborate types of woofers). It explained well how to properly install subs facing into the cabin in a sedan to eliminate the bass cancellation and reduce bass lost to panel vibrations. Basically comes down to how well you seal off the gap between the cabin and subs, and the boot.

How exactly were you planning on putting the sub behind the drivers seat?

given that a bass wave is rather long (in some cases 30ft!) and you have it right behind you - are you going to get 'best effect' vs having it far away as possible (IE boot.) ?

that wave needs to expand to really be felt/heard.

You will also gain some response and volume from the cabin gain that you will get when in the boot.

buy a Porsche 911 then put the sub in front of you ,, bass in ya face. thru the air vents under the dash

did a LAMBO and 512 Ferrari that way, 8" solobaric in fiberglass box using the floor space under your feet on the passenger side. nice tight bass

but not lots of SPL to shake the ground with

you dont have to remove a spare to have good Bass,,, Im so tired of preaching that..lol

the skyline has more then enough room to be creative to get bass inside it without firing the sub into the boot which creates muddy boomy bass "in most cases " and rattles the hell out of them , Most Skylines have steel plates between the rear seat and boot anyhow but hidden between the rear seat and side panels is a big void. or more then enough room to port bass thru to the front , another choice , remove the rear speakers, port the bass thru the holes which will give you even more cabin gain as the wavelength of sound bounces off the shape of the glass backwindow = higher SPL

or port thru the back seat similar to using a 4dr seat with armrest /ski tunnel passthru to the boot . which gives a purer SPL, tighter bass.

a sealed, or bandpass box works a treat and can be sealed off from the boot area easy the GTT Sat Nav computer will need relocating but nothing else.

some GTR and cars with rear strut braces may need some tweaking to work but still not a worry

these are LEGAL ways, if your game to run the gauntlet of defects you can go crazy and cut the rear deck with ports and speakers.

putting a speaker in the floor isnt legal if you cut it or place the driving compartment in jeopardy of crashing in anyway(boxes that consume the drivers feet or passenger safety in anyway.

u dont need spare tyres
Spare tyres are for pussies.

not the space saver, just a spare 2 rims just incase i ever feel the need to pop my rear ones on-road.

How exactly were you planning on putting the sub behind the drivers seat?

i was gonna have the direction of the sub, facing the back window on an angle from the floor.

the skyline has more then enough room to be creative to get bass inside it without firing the sub into the boot which creates muddy boomy bass "in most cases " and rattles the hell out of them , Most Skylines have steel plates between the rear seat and boot anyhow but hidden between the rear seat and side panels is a big void. or more then enough room to port bass thru to the front , another choice , remove the rear speakers, port the bass thru the holes which will give you even more cabin gain as the wavelength of sound bounces off the shape of the glass backwindow = higher SPL

or port thru the back seat similar to using a 4dr seat with armrest /ski tunnel passthru to the boot . which gives a purer SPL, tighter bass.

a sealed, or bandpass box works a treat and can be sealed off from the boot area easy the GTT Sat Nav computer will need relocating but nothing else.

some GTR and cars with rear strut braces may need some tweaking to work but still not a worry

yeah i tried removing the rear speakers and having the sub going threw the holes though the fact is, i still had the sub in the boot which eh i don't like so much... previous owner put a 12" with a massive box which almost touches both struts. was thinking of maybe getting 8".

thanks for the replies all,

(ps. im not a bass pumping kid haha, i just want most usage out of my boot and also have some bass for kicks... nothing muzza)

Edited by silbastian

its easy mate, even a quality 8 or 10 will hit 130db or more with modest power and sound tight and punchy, clear

the box size doesnt need to be much bigger then a big shoe box either. any custom stereo installer should be more then capable of a design to fit your needs. and regain all of your boot back, your shocks will thank you and so will your performance of your car over the dead weight of a big box.

and spare tires ....sure beat walking ... or sitting by the road waiting for the roadside assistance guy to tell you your a putz for not having a spare in middle of whoop whoop(outback)!!!!...lol

get a flat with a chick in the car, she will wait!!!!!.........for the next car that pulls up to leave ya on the roadside alone..lol

its easy mate, even a quality 8 or 10 will hit 130db or more with modest power and sound tight and punchy, clear

the box size doesnt need to be much bigger then a big shoe box either. any custom stereo installer should be more then capable of a design to fit your needs. and regain all of your boot back, your shocks will thank you and so will your performance of your car over the dead weight of a big box.

and spare tires ....sure beat walking ... or sitting by the road waiting for the roadside assistance guy to tell you your a putz for not having a spare in middle of whoop whoop(outback)!!!!...lol

get a flat with a chick in the car, she will wait!!!!!.........for the next car that pulls up to leave ya on the roadside alone..lol

our fitter at work made 140db with a single 10... :blink: easy as.

I had my Alpine Type R 12" (with ported Alpine box) in the boot of my 33. Rattled the absolute shit out of my car. Sounded good on the inside, but even on a relatively low volume the boot rattled like a mofo and was embarassing.

In my new Supra the box won't even fit in the boot (well, hatchback) of the Supra. It sits directly behind the driver which suits me fine because I HATE driving with a passenger behind me. Gives me the perfect excuse not to take more than 2 people at once. Sounds great now, especially with the windows open.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 65601-05U00 is the hood latch. 62550-08U31 is the support that holds it to the radiator core support. They are all super discontinued so I don't really have any great leads on how to source this stuff.
    • GTSBoy on your suggestion on another thread I had a look at those injectors and ended up getting them because of the quality.  Got the expensive ones.  
    • Hey guys been looking everywhere to try and find the correct gtr hood latch support part number but only found the first half and when I search with that number it sends me to an r34. The first part I found was 62515. If anyone could help me with the rest then I’d really appreciate it. Or if there’s some alternative hood latch support that would work even better cause I can’t find any for sale. (Searched on upgarage, partsouq,buyee,rhdjapan) 
    • If you've only done the upper control arms on the rear, AND you have changed their length (by more than about 1mm) to set the camber you want, then you will definitely need/want to install traction arms also. Adjusting the camber arms on their own WILL introduce bump steer and make the car unpleasant to drive. Most owners have no idea that their car could behave infinitely better than what they put up with. I'm not entirely sure what the Stageas need, but I am thinking that unless you have massive front spring rates and pretty soft rear springs, you have waaaay too much rear bar. Oversteer city, in my estimation. Combined with possible excessive bump steer from maladjusted arms, that could be a recipe for nastiness. ATR43SS2 is not a highflow. It is an outright replacement turbo. It's a little bit bigger than the largest highflow profile that Tao does. Probably a solid 300rwkW turbo where the bigger highflows will be about 30-40rwkW less. Nevertheless, we're only talking about ~300 rwkW, which is well within the abilities of the stock ECu to run with a Nistune on board. I would do so without hesitation - and I will be doing so when I get my finger out and actually get the injectors and AFM installed. But, if you would prefer to drop a whole lot more money on the ECU side, then I suspect you're looking at Haltech. The Haltech fanbois here will all spout on about all the available engine protection you can have, that you can't have with the Nistune option. And they're right. But it doesn't really come for free either. You will spend more money on extra sensors and the like, plus the work to install them. If the engine was built and therefore represented a big investment to protect, then I'd say definitely do it. If you view the current (and forever into the future) shortage of replacement engines as something to prompt similar protection, then also, do it. If you see a destroyed RB25 as an opportunity to put in a Mercedes or other V12 (like I kinda do)... then your perception of the risk/reward might differ. These are good injectors. You can also get a "better" set of the same with more flow matching, for more $$. 1000cc is where you will want to be. You will need an R35 AFM and adapter tube if you want to stay with Nistuned stock ECU. Otherwise, if going Haltech, you can ignore. As for intercooler. Just about anything will do. You're only talking about ~300rwkW. Just put a big core in there. Be aware that return flows do add significant pressure drop and will cost power and will make the turbo work harder to achieve the same goals. If you can manage a proper crossflow, do it. I'm keeping my very good return flow because I'm only expecting to be in the ~250rwkW range, and will live with whatever outcome I get.
×
×
  • Create New...