Jump to content
SAU Community

Recommended Posts

Agreed - very cool - have been meaning to try it sometime but haven't yet.

There are two ways to do it - the proper way (as gadl above does)

and the cheating way where you take one pic and do it in PS in 3 steps

(obviously not as good!)

Here for example is one I made the cheating way (pretty crap)

before

2009_02_05%20Brisbane%20CBD.jpg

after

2009_02_05%20Brisbane%20CBD%20Land.jpg

Link to comment
https://www.sau.com.au/forums/topic/297679-wee-planets/#findComment-4954920
Share on other sites

1. Convert the photo into a square image

Use the Photo|Image Size menu item to change the image size into a large square. Uncheck ‘Constrain Proporties’ and set the “height” value to the same value as your “width” value.

2. Turn image upside down

Rotate by 180°

3. Apply the polar effect

“Filter|Distort|Polar Coordinates” filter - choose the “Rectangular to Polar” setting

When selecting a photo to start with you should keep the following things in mind:

  • Select a panorama photo or a cropped landscape photo (aspect ratio at least 2:1, which means the width should be at least two times the height).
  • The bottom area (bottom 25% or so) of the photo in most cases should have only very little detail (e.g. sand, asphalt, water). This area will later be in the middle of the picture and will also be distorted the most.
  • The upper area (upper 25%) should also have only little detail, most preferably just one color (e.g. blue sky, night sky etc.).
  • The left and the right border of the photo should neatly fit into each other (which is always the case for a stitched 360° panorama).
  • The horizon must be exactly horizontal, the left and right end of the photo will be joined together and if they are on different heights your planet will have a big crack in the surface (again this is no issue for 360° panoramas).
Link to comment
https://www.sau.com.au/forums/topic/297679-wee-planets/#findComment-4955114
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi all, I’m currently running a str pipe hi low hks exhaust and downpipe. Was wondering if I change out muffler to a titanium one will it change the sound of the exhaust? Plus I have always liked the look of the titanium pipes … anyone have recommendations to one?    side note already have titanium intake pipes. 
    • I looked up my other car that is a R33 GTST series 1.5. Anyone able to confirm what a Aero Form Bumper is?     (1G) 2 Door Coupe; (2GK + 11V) RB25DET; (4B) 2WD HICAS; (7F) 5 Speed Manual; (14G) Super Fine Hard Coat; (15U) Large Rear Spoiler + Aero Form Bumper + Rear Wiper (Aero Selection)
    • Ha ha, all good! I've almost caved in and realised I'm buying one.  I know myself well enough by now that I will start chasing ADHD butterflies half way through building it and not finish it so I'm better off spending the extra money buying one instead of making one just so I can get into straight away.  I would very much enjoy making one as fabrication is probably a strength and definitely a passion but I don't want that to be at the detriment to the car I'm ultimately building it for! There's some pretty good ones around for ~$1100 at the moment so I think I'll just go that way.  At the end I sell it or as mentioned, get another project to make further use of it! Thanks gents.  
    • That link was very helpful thank you.
    • That is the option code, not the VIN. Regardless all of that production is considered series 2: https://gtr-registry.com/en-ecr33-vin-table.php
×
×
  • Create New...