Jump to content
SAU Community

Recommended Posts

Just realised they ran the bimmer in 3rd. Why not 4th? Its a 5 speed and has tiptronic so it would hold gears....

Because auto cars have a 1:1 ratio in 3rd gear.. As opposed to manual cars in 4th.

  • Replies 224
  • Created
  • Last Reply

Top Posters In This Topic

5-speed automatic ZF 5 HP 24 EH.

Ratios ( r : 1):

Ratio : 1

Top Speed @ 6,000 RPM

1st 3.57 39 MPH

2nd 2.20 63 MPH

3rd 1.51 92 MPH

4th 1.00 139 MPH

5th 0.83 155 MPH @ 5,500 RPM*

The manual is a 6 speed, so 5th is required for 1:1.

Edited by Ten Four
Dyno is about right with 500+rwhp in a 10sec car.

Sounds like the guys at Autoworx did a good job.

So we come to the conclusion Hypers n Advans dynos are out 150+ hp :( , what MPH should we be running if the 500 hp is right ???

134/137MPH. Jeffs 480rwhp 10.4 was at 136mph. Most 10sec V8s I do are from 450 to 500rwhp running GTR weight.

Really big HP Turbo cars are often slower because you need large Turbos etc giving way to much Lag needing dedicated Gearbox's etc.

Your GTR running 10s and also working well on a race track would be a very smart 500rwhp (Board power curve) with 2 people in the car.

Huge topend power does not make for a fast car, Fat Power / Torque curves do.

5-speed automatic ZF 5 HP 24 EH.

Ratios ( r : 1):

Ratio : 1

Top Speed @ 6,000 RPM

1st 3.57 39 MPH

2nd 2.20 63 MPH

3rd 1.51 92 MPH

4th 1.00 139 MPH

5th 0.83 155 MPH @ 5,500 RPM*

The manual is a 6 speed, so 5th is required for 1:1.

Well there you go, as you can see I didn't research my repsonse in terms of your car :(

5-speed automatic ZF 5 HP 24 EH.

Ratios ( r : 1):

Ratio : 1

Top Speed @ 6,000 RPM

1st 3.57 39 MPH

2nd 2.20 63 MPH

3rd 1.51 92 MPH

4th 1.00 139 MPH

5th 0.83 155 MPH @ 5,500 RPM*

The manual is a 6 speed, so 5th is required for 1:1.

I chose 3rd because I wanted a roller speed between 120 and 180km/hr, in accordance with standard shoot-out proceedure. There's more to it than gearbox ratio - it's overall final drive that matters.

The GTR of the Bart only made 518hp because it was blowing the tyres off. Big deal. I ran the car in 4WD first up and it made good numbers at all 4. The dyno wasnt down. The car wasnt down. 540 or whatever it made at all corners is damn respectable, and backs up the time slips. The low figure in RWD was an issue of coupling one to the other. Do we have any other AWD dyno figures to compare it to?

They probably thought it had 1:1 in 3rd, I doubt they dyno many Beemers.

Levi, fantastic pics mate! I'll have to have a chat with you next time, grab a few tips off you! Can I grab a higher resolution picture of my car?

No problem, always happy to talk cameras.

Bigger Picture

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Also had a look at the Nissan JP website looks like the 400r has a slightly shorter ratio than than the regular V37 3.133 VS 2.937 which from a guy who has driven both 3.69 vs 4.11 ratios in the S15 is bugger all. Seems that the AUTO Z runs the same ratio as the 400R but can't find any info as to if its an open or LSD? More often than not the auto LSD is open
    • Do not replace the power steering lines with this stuff. If it's anything like the Chase Bays stuff it will leak and be worse than stock. The reason why the reservoir is on the LH/passenger side of the car is because that's just where the reservoir was most convenient to fit. Don't overthink this stuff. The intake/cold side of the engine is pretty busy on these cars. And again, the hardpipe is designed to be a janky power steering cooler. In theory you can replace it with a real power steering cooler but that's really only for track use where boiling the fluid is a distinct possibility. Start with the low pressure lines feeding the pump from the reservoir. Make sure there isn't a bunch of junk in the reservoir filter. Be careful to not get ATF all over the engine bay. I hate dealing with ATF spills, you can clean it up and the slightest crevice will still release more oil that can still drip over time. You also want to inspect for leaks before you make a mess and can't tell what happened. Most likely you have a leak somewhere that is allowing fluid out and air in. Failing that it's allowing air in but not fluid out. Only place I can really see that happening is on the low pressure side because the pump will pull a slight vacuum to draw fluid in. Everything after the pump is high pressure or lower pressure, approaching atmospheric by the time it returns to the reservoir.
    • I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
    • Do you have an IAT sensor? It's worth checking it to see. You may be suprised how little gap you actually need to flood your engine with hot air. (I tape up my airbox for a reason) :p
×
×
  • Create New...