Jump to content
SAU Community

Recommended Posts

hey guys,

one of my rear shockers started leaking recently, just wondering where i could pickup a replacement for a good price? I only know of pedders and they charge $225 per shock..

Also is it ok if i replace one shock since theres only one leaking? or will it screw up the balance of the car or something?

Thanks in advance

EDIT: Did some calling around:

Autobarn

Kyb ~$169 each

Koni ~$260 each

Bursons $185 for the pair (Monrow)

Bursons seem pretty decent for $185 for the pair.. could anyone tell me if Monrow shockers are any good?

Edited by shaun123
Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/
Share on other sites

if one is stuffed - the other probably wont be far behind so you would replace the two at the same time to be honest.

pedders are probably going to be the cheapest option.

just ring around, and then check the suspension section for reports of the products

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4958691
Share on other sites

LOL!

Monroe shocks... In a Skyline...

I will put them in my daily driver but not for a Skyline.

KYB and Koni are both good.

I'd go Koni for your Skyline or any Japanese brand if you got the cash.

http://farnorthracing.com/autocross_secrets6.html :)

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4960135
Share on other sites

Haha!!

Meh.

Yeah Bilstein's are great, but I don't see any Japanese brands test there and I am pro Japanese when it comes to Skylines, with a few exceptions.

The Yanks can crap on about NASCAR but not much turning is required in that motorsport.

Yes suspension set up is important, getting the correct ride height and setup will gain to your take off and going in a straight line, but we all know handling through corners is where the suspension will have to prove itself.

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4961348
Share on other sites

Haha!!

Meh.

Yeah Bilstein's are great, but I don't see any Japanese brands test there and I am pro Japanese when it comes to Skylines, with a few exceptions.

The Yanks can crap on about NASCAR but not much turning is required in that motorsport.

Yes suspension set up is important, getting the correct ride height and setup will gain to your take off and going in a straight line, but we all know handling through corners is where the suspension will have to prove itself.

that was just one link.

numerous times "green" shocks are mentioned :P

I have teins, I would never buy them, they came with my car.

Gary Cook/SK, sets up race cars, anti jap shit.

Another suspension engineer(who's name i wont post as i dont know if they would want it dragged into it) Told me that bilsteins are pretty much the minimum even for a street car, and not to touch the jap shit off the shelf.

I had koni's in one of my cars, but they take some fidling to get right, and it wasn't driven enough to see the rumored reliability issues. Unlike bilsteins, work well off the shelf if you match the springs, and no reliability issues in the sets I have had(and from what reading on the topic I have done)

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4962087
Share on other sites

that was just one link.

numerous times "green" shocks are mentioned :(

I have teins, I would never buy them, they came with my car.

Gary Cook/SK, sets up race cars, anti jap shit.

Another suspension engineer(who's name i wont post as i dont know if they would want it dragged into it) Told me that bilsteins are pretty much the minimum even for a street car, and not to touch the jap shit off the shelf.

I had koni's in one of my cars, but they take some fidling to get right, and it wasn't driven enough to see the rumored reliability issues. Unlike bilsteins, work well off the shelf if you match the springs, and no reliability issues in the sets I have had(and from what reading on the topic I have done)

Nothing wrong with Teins.

A friend of mine had them in his R32 GTR and was a nice comfortable ride and handled great. Mind you, his car was stock but with Tein's, so for a daily car at the time, it did the job and very well.

"Green was mentioned once in the article, "shiny green or purple shocks..." Probably referring to Tein (Green) and HKS (purple).

Gary, who..?

Meh... If the suspension engineer who you won't name, has done test to prove why they won't buy Japanese suspension bands, then naming them on here, won't hurt, what they got to lose, unless they can't back up what they claim / tested...

Post it, I will be interested in what they have to say.

Again, in that article you posted, yes I do agree, Bilstein, Koni and Ohlins are great, remember "I am pro Japanese when it comes to Skylines, with a few exceptions.".

Depending on the product, the few exceptions can be quite a lot...

:O

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4963255
Share on other sites

All good to recommend Bilstein but they command greater amounts of the plastic stuff ($$$$) Rears for my 32R were roughly $550 each!! Front weren't much better at around the $450 mark. KYB and Koni are great and a damn sight cheaper than the billy's.

Tein are also fine, I think of them as BilsTEIN without the BIL$ attached!! lol

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4963756
Share on other sites

All good to recommend Bilstein but they command greater amounts of the plastic stuff ($$$$) Rears for my 32R were roughly $550 each!! Front weren't much better at around the $450 mark. KYB and Koni are great and a damn sight cheaper than the billy's.

Tein are also fine, I think of them as BilsTEIN without the BIL$ attached!! lol

:)

Nice one buddy!

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4963784
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yeah, all the crude is used for fuels and petrochem feedstocks (pesticides, many other chemicals, etc etc). But increasingly over the last few decades, much of the petrochem synthessis has started with methane because NG has been cheaper than oil, cleaner and easier and more consistent to work with, etc etc etc. So it's really had to say what the fraction either way is. Suffice to say - the direct fuels fraction is not insigificant. Heavy transport uses excruciatingly large amounts. Diesel is wasted in jet heaters in North American garages and workshops, thrown down drill holes in quarries, pissed all over the wall to provide electricity to certain outback communities, etc etc. Obviously road transport, and our pet project, recreational consumption camouflaged as road transport, is a smaller fraction of the total liquid HC consumption again. If you're talking aboust Aussie cars' contribution to the absolute total CO2 production of the country, then of course our share of the cubic mile of coal that is used for power generation, metallurgy, etc adds up to a big chunk. Then there is the consumption of timber. Did you know that the production of silicon metal, for example, is done in Australia by using hardwood? And f**king lots and lots and lots of hardwood at that. Until recently, it was f**king jarrah! There are many such sneaky contributors to CO2 production in industry and farming. NG is used in massive quantities in Australia, for power gen, for running huge water pumps (like, 1-2MW sized caterpillar V16 engines running flat out pumping water) for places like mine sites and minerals/metals refineries. And there are just a huge number of those sort of things going on quietly in the background. So NG use is a big fraction of total CO2 production here. I mean, shit, I personally design burners that are used in furnaces here in Oz that use multiple MW of gas all day every day. The largest such that I've done (not here in Oz) was rated to 150MW. One. Single. Gas burner. In a cement clinker kiln. There are thousands of such things out there in the world. There are double digits of them just here in Oz. (OK< just barely double digits now that a lot of them have shut - and they are all <100MW). But it's all the same to me. People in the car world (like this forum's users) would like to think that you only have to create an industrial capability to replace the fuel that they will be using in 10 years time, and imagine that everyone else will be driving EVs. And while the latter part of that is largely true, the liquid HC fuel industry as a whole is so much more massive than the bit used for cars, that there will be no commercial pressure to produce "renewable" "synthetic" fuels just for cars, when 100x that much would still be being burnt straight from the well. You have to replace it all, or you're not doing what is required. And then you get back to my massive numbers. People don't handle massive numbers at all well. Once you get past about 7 or 8 zeros, it becomes meaningless for most people.
    • @GTSBoy out of the cubic mile of crude oil we burn each year, I wonder how much of that is actually used for providing petrol and diesel.   From memory the figure for cars in Australia, is that they only add up to about 2 to 3% of our CO2 production. Which means something else here is burning a shit tonne of stuff to make CO2, and we're not really straight up burning oil everywhere, so our CO2 production is coming from elsewhere too.   Also we should totally just run thermal energy from deep in the ground. That way we can start to cool the inside of the planet and reverse global warming (PS, this last paragraph is a total piss take)
    • As somebody who works in the energy sector and lives in a subzero climate, i'm convinced EV's will never be the bulk of our transport.  EV battery and vehicle companies over here have been going bankrupt on a weekly basis the last year. 
    • With all the rust on those R32s, how can it even support all the extra weight requirements. Probably end up handling as well as a 1990s Ford Falcon Taxi.
    • Yes...but look at the numbers. There is a tiny tiny fraction of the number of Joules available, compared to what is used/needed. Just because things are "possible" doesn't make them meaningful.
×
×
  • Create New...