Jump to content
SAU Community

Recommended Posts

hey guys,

one of my rear shockers started leaking recently, just wondering where i could pickup a replacement for a good price? I only know of pedders and they charge $225 per shock..

Also is it ok if i replace one shock since theres only one leaking? or will it screw up the balance of the car or something?

Thanks in advance

EDIT: Did some calling around:

Autobarn

Kyb ~$169 each

Koni ~$260 each

Bursons $185 for the pair (Monrow)

Bursons seem pretty decent for $185 for the pair.. could anyone tell me if Monrow shockers are any good?

Edited by shaun123
Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/
Share on other sites

if one is stuffed - the other probably wont be far behind so you would replace the two at the same time to be honest.

pedders are probably going to be the cheapest option.

just ring around, and then check the suspension section for reports of the products

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4958691
Share on other sites

LOL!

Monroe shocks... In a Skyline...

I will put them in my daily driver but not for a Skyline.

KYB and Koni are both good.

I'd go Koni for your Skyline or any Japanese brand if you got the cash.

http://farnorthracing.com/autocross_secrets6.html :)

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4960135
Share on other sites

Haha!!

Meh.

Yeah Bilstein's are great, but I don't see any Japanese brands test there and I am pro Japanese when it comes to Skylines, with a few exceptions.

The Yanks can crap on about NASCAR but not much turning is required in that motorsport.

Yes suspension set up is important, getting the correct ride height and setup will gain to your take off and going in a straight line, but we all know handling through corners is where the suspension will have to prove itself.

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4961348
Share on other sites

Haha!!

Meh.

Yeah Bilstein's are great, but I don't see any Japanese brands test there and I am pro Japanese when it comes to Skylines, with a few exceptions.

The Yanks can crap on about NASCAR but not much turning is required in that motorsport.

Yes suspension set up is important, getting the correct ride height and setup will gain to your take off and going in a straight line, but we all know handling through corners is where the suspension will have to prove itself.

that was just one link.

numerous times "green" shocks are mentioned :P

I have teins, I would never buy them, they came with my car.

Gary Cook/SK, sets up race cars, anti jap shit.

Another suspension engineer(who's name i wont post as i dont know if they would want it dragged into it) Told me that bilsteins are pretty much the minimum even for a street car, and not to touch the jap shit off the shelf.

I had koni's in one of my cars, but they take some fidling to get right, and it wasn't driven enough to see the rumored reliability issues. Unlike bilsteins, work well off the shelf if you match the springs, and no reliability issues in the sets I have had(and from what reading on the topic I have done)

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4962087
Share on other sites

that was just one link.

numerous times "green" shocks are mentioned :(

I have teins, I would never buy them, they came with my car.

Gary Cook/SK, sets up race cars, anti jap shit.

Another suspension engineer(who's name i wont post as i dont know if they would want it dragged into it) Told me that bilsteins are pretty much the minimum even for a street car, and not to touch the jap shit off the shelf.

I had koni's in one of my cars, but they take some fidling to get right, and it wasn't driven enough to see the rumored reliability issues. Unlike bilsteins, work well off the shelf if you match the springs, and no reliability issues in the sets I have had(and from what reading on the topic I have done)

Nothing wrong with Teins.

A friend of mine had them in his R32 GTR and was a nice comfortable ride and handled great. Mind you, his car was stock but with Tein's, so for a daily car at the time, it did the job and very well.

"Green was mentioned once in the article, "shiny green or purple shocks..." Probably referring to Tein (Green) and HKS (purple).

Gary, who..?

Meh... If the suspension engineer who you won't name, has done test to prove why they won't buy Japanese suspension bands, then naming them on here, won't hurt, what they got to lose, unless they can't back up what they claim / tested...

Post it, I will be interested in what they have to say.

Again, in that article you posted, yes I do agree, Bilstein, Koni and Ohlins are great, remember "I am pro Japanese when it comes to Skylines, with a few exceptions.".

Depending on the product, the few exceptions can be quite a lot...

:O

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4963255
Share on other sites

All good to recommend Bilstein but they command greater amounts of the plastic stuff ($$$$) Rears for my 32R were roughly $550 each!! Front weren't much better at around the $450 mark. KYB and Koni are great and a damn sight cheaper than the billy's.

Tein are also fine, I think of them as BilsTEIN without the BIL$ attached!! lol

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4963756
Share on other sites

All good to recommend Bilstein but they command greater amounts of the plastic stuff ($$$$) Rears for my 32R were roughly $550 each!! Front weren't much better at around the $450 mark. KYB and Koni are great and a damn sight cheaper than the billy's.

Tein are also fine, I think of them as BilsTEIN without the BIL$ attached!! lol

:)

Nice one buddy!

Link to comment
https://www.sau.com.au/forums/topic/297963-shockers/#findComment-4963784
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yes...but look at the numbers. There is a tiny tiny fraction of the number of Joules available, compared to what is used/needed. Just because things are "possible" doesn't make them meaningful.
    • Thanks for taking the time to post that ! If anything changes or happens please do update us. 
    • Somehow Vertimass/Oak Ridge National Labs has figured out a catalyst that can convert ethanol into C9-C10 hydrocarbons in basically a single step without ending up with a bunch of ethylene or similar waste products: https://patents.google.com/patent/WO2023224867A1/en I still don't think anything like this will keep us from needing to transition to EVs regardless along with all kinds of other electrification, but things like this will go a long way towards alleviating the problem of how to electrify things like planes. Renewable diesel is seemingly an easier problem as well, Chevron is already running refineries for the stuff and the primary feedstock is tallow and other waste fats from agriculture.
    • Ok so I have sorted everything with my uniclutch and  i can offer up a bit of feedback and some things that might help others.    I found problems with factory damper line. Weird shit and had trouble with peddle adjustment    I used this https://au.gktech.com/products/r33-gts-t-skyline-braided-clutch-line?_pos=2&_sid=22b01b9b9&_ss=r Also when adjusting peddle leave a bit of play. You can get into a over stroke condition easy.. Make sure you can push the slave forward after adjusting to confirm fluid can return to master then you will need to pump it up heaps…..not sure why but that’s how it is.    last thing the splined adapter is machined perfectly. If your input shaft is old like mine was I would put a bit of valve grinding paste on it and stroke it like a 15 year old. Just to give it a tad more clearance and to better match it to the spline.    reason is on a near flat shift I have had situation where the peddle returns a millisecond after you lift from the clutch. No slip or anything but I reckon this is due to tolerance on the spline being way tighter than stock clutch and binding for a sec. I think this will go away but also my spline was old. Box is old so I guess I should have checked better. It’s a super neat fit.    it feels light as and holds awesome without any noise    
    • My Fuga Hybrid is JDM, 2014 model but very similar to the V37 from the looks of things..same platform just physically larger and very comfortab;e
×
×
  • Create New...