Jump to content
SAU Community

Recommended Posts

hey guys and gurls

jst recently put a gfb bov on the r33 but didnt like it to much so took it off

but noticed that my stock boost guage was at -7 at idle now i put my stock bov on

and it sits a bit before-7 :s

cars still runing fine jst like it was before

turbo still excatly the same

could of it thrown out the boost gauge some how?

cheers guys

It'll be fine, just remember that you altered a part of the system that's supposed to stay pressurised.

The stock blow off valve is designed to leak a little bit when at idle, so I would suggest that changing from the GFB one (which wouldn't leak at idle) to the stock one would change your reading.

Cheers guys I was worried at first but the car is still

mechanicly sound , cheers guys I'll check the vac line tomorrow if I was to change my bov

would I need to get a tune or somthing coz I was looking to buy the greddy type s

Cheers guys I was worried at first but the car is still

mechanicly sound , cheers guys I'll check the vac line tomorrow if I was to change my bov

would I need to get a tune or somthing coz I was looking to buy the greddy type s

Dont bother getting a tune if your only changing a BOV. If it is Recirculating back into the intake then nothing changes. If it is atmospheric then a tune wont really help unless you find an alternative to the factory Air Sensor (And even then you would only have to worry about the possible stalling issues caused by Atmo BOV's as covered in many, many a post before this)

Save the tune for big mods like injectors, turbos etc.

Luke

ahhh ok. im sure nissan would have designed a vacuum leak into the intake system to aid smooth idle lol.

It'll be fine, just remember that you altered a part of the system that's supposed to stay pressurised.

The stock blow off valve is designed to leak a little bit when at idle, so I would suggest that changing from the GFB one (which wouldn't leak at idle) to the stock one would change your reading.

Even if the BOV is designed to leak, it's a NOT going to affect idle as the "leak" is not escaping outside of the air measured by the AFM.

I don't see, how at idle, the stock BOV is going to be "leaking".

Air flows from point of highest pressure to lowest. When idling, the WHOLE intake up until the throttle body is at the same pressure...

The vacuum point is from the throttle body to motor side... Nothing to do with before it...

I don't see, how at idle, the stock BOV is going to be "leaking".

Air flows from point of highest pressure to lowest. When idling, the WHOLE intake up until the throttle body is at the same pressure...

The vacuum point is from the throttle body to motor side... Nothing to do with before it...

Maybe it leaks backwards :blink:

I don't see, how at idle, the stock BOV is going to be "leaking".

Air flows from point of highest pressure to lowest. When idling, the WHOLE intake up until the throttle body is at the same pressure...

The vacuum point is from the throttle body to motor side... Nothing to do with before it...

Except for the fact there's a vacuum line (from after the throttles) to the top of the bov which would suck it open unless the spring held it shut. the factory spring tension is soft enough to allow a small leak at idle.

Except for the fact there's a vacuum line (from after the throttles) to the top of the bov which would suck it open unless the spring held it shut. the factory spring tension is soft enough to allow a small leak at idle.

Even if the bov were fully opened, pressure on the air filter side, and the IC pipe side is EQUAL, so there is no "leak".

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This was a huge help.  We followed the steps,  although shifting into 2nd was actually into 3rd for us,  and 1st was into 2nd ( steps 9 and 11) .  The long flash was the 4th flash.  So shift solenoid A is possibly the culprit.  Is this inside the transmission itself? Or is it accessible by just front the pan? Or is it bolted to the outside of the transmission?  Thanos for your help everyone
    • Can you enlighten me on your best practice regarding these hoses? I don't wanna make the same mistake if you already got a better solution.
    • I have some silicon hoses already, for example engine to watercooler. But yeah, I get the sentiment. The lower intercooler silicon hose is drippy too, despite not being very old. Does anyone except Nismo make these same lines out of rubber? Long term I think they'd be the better replacement, especially since the car won't live as hard a life anymore as in the past nor be driven as often.
    • I know most issues are just age related. But for example the turbo oil drains, there is dash adapters for these and you can just make a braided teflon line for them and (probably) never have them leak again. Also not terribly expensive. Can you even get the factory hardlines from new? Or are they repairable if they break?
    • I know it'd be much much easier with the tool. I hope I can find one that won't take 3 weeks to get to me an isn't a "Asian models kit" that has tons of (to me) useless adapters for a load of cash.   It's a summer project/fun car. I do wanna enjoy it, without endless downtime over and over. So yeah I would even go and buy an engine crane + stand to save myself the trouble of hard to reach or unreachable places going bad later on. Would also be a good opportunity to put on a Fluidamper, renew the mains seals and stuff like that. I have some money on the side that I can use for that, what I wouldn't want to or be able to do is let everything be done by a shop or have my engine completely rebuild right now. I intend to do most of the "doable" jobs myself. Pulling an engine can't be that hard, can it?
×
×
  • Create New...