Jump to content
SAU Community

Recommended Posts

Ok I am new to the forums and millimeters away from purchasing my first skyline (93 r33 gtst), BUT there's one problem the aircon does not work.

Has anyone experienced any aircon problems and or had to replace any parts? Are the parts readily available to start with?

Need to know worst case scenario of how much it will cost to repair so I can account for it in the purchase price.

All feedback will be appreciated.

Cheers,

Tay

Link to comment
https://www.sau.com.au/forums/topic/29898-aircon-problems/
Share on other sites

Well I have a 93 R33 as well but haven't had any problems with the aircon. Except i had to get it regassed the other day for the princely sum on $99 inc labour.

Unless the car is an absolute bargain don't buy it with obvious problems, just move on to the next Skyline. There's a million around.

Parts for the aircon will be available easily and any aircon place will be able to work on it. The only issue is if you need to replace major parts like the compressor or get the entire system repiped.

Worst case you're looking at up to two grand including diagnosing the problem.

In other words, it could cost you more than the difference between this car and another bargain R33.

Link to comment
https://www.sau.com.au/forums/topic/29898-aircon-problems/#findComment-608356
Share on other sites

Hmm..2K?? that's sounds pretty steep.

This car ain't quite a bargain but I think I am willing to take a punt (and just hope it's a quick fix). I will have to take a significant chunk out of the offer though.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/29898-aircon-problems/#findComment-609810
Share on other sites

when you say not working, what do you mean? If the fans are going but you're only getting warm air it could be the coolent needs replacing, or there could be a leak in the system. If you're not even getting the fans going, the problem could be electrical.

Also be aware that sometimes Japanese owners will strip out the aircon system to save weight and avoid losing power! I've seen this done to a couple of cars.

Link to comment
https://www.sau.com.au/forums/topic/29898-aircon-problems/#findComment-609945
Share on other sites

Ok against all advice it would seem I have bought the car and am very very pleased to become a Skyline owner for the first time (yeehaa!!!).

I managed to negotiate a few hundred off the already haggled price so I am not too displeased. Perhaps I should let a pro have a look at it before I get too excited. Aircon is all there it just blows hot air....hmm anyway I will let you know.

Thanks for the help.

Link to comment
https://www.sau.com.au/forums/topic/29898-aircon-problems/#findComment-611187
Share on other sites

This is the first thing I will try.

Apparently nothing will work if the gas gets to a certain (low) level. Hope this theory is true. As long as everything works and its just got a leak (be it major or minor) I will be happy to get it fixed.

Coz damn its hot in Perth.

Link to comment
https://www.sau.com.au/forums/topic/29898-aircon-problems/#findComment-611757
Share on other sites

afaik a/c's have a pressure switch, when the pressure gets to low, the switch breaks the circuit so that the clutch cannot engage.

sorry they don't have a low pressure switch at all reason you think clutch isn't engaged is because no gas = no load from compressor.

they only have a high pressure switch to cut out compressor, you need this because most car a/c regas places overcharge.

your a/c runs but only hot air comes out means only 2 things low gas or compressor not pumping, now there are to many reasons to list causes but most common is compressor seal leaks due to wear & only fix is reco compressor (car compressor is belt driven so mech esal is side loaded so any bearing wear or over tighten belt causes seal to wear faster causing gas to leak because it's the sealing medium).

car a/c systems hold very little refrigerant charge with most holding under 1kg which to put in dollars in cost if you have lic (like me) to buy it is about $20 per kg R134a.

Link to comment
https://www.sau.com.au/forums/topic/29898-aircon-problems/#findComment-612026
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
×
×
  • Create New...