Jump to content
SAU Community

Recommended Posts

Hi all :down:

so i was wiring the IEBC into my wife's stag last night and something's gone wrong.

I've got my power source and ground for certain (pin 31 for ignition power, pin 32 for ground). I've also grabbed what i thought was injector 1 cycle (pin 101) and the solenoid control (104). i'm relatively confident that i've got the solenoid right, which would lead me to believe i've got the wrong signal from what i thought was the injector wire.

problem is, according to the ecu pin-out, it's all apples. the only thing that i can think of that's overdrive related is pin 115 which is "overrun clutch solenoid valve control signal", which is miles away from the wire that i've spliced for injector signal...

. i'm referencing the R34 ecu pin out diagram btw, which i've been told is the same as the s2 stagea.

if anyone's got any ideas at all, i'd be greatly appreciative. i have a long trip ahead of me very soon, so would like (at least) my overdrive back! :blink:

cheers guys :)

josh

Edited by pyro-ns

Strange indeed. Your pin numbers are as per the S1 pinout that I have. Also strange because the only circuit you are breaking is the one to the boost solenoid - you are only tapping into the other ones. In the s1 there is an overdrive on/off switch but i believe the s2 doesn't have that?

I've just noticed that (on my chart at least) pin 104 is directly above (well two places above)) pin 120 lockup solenoid valve control signal. If you have your IEBC connected you can with ignition on engine off, by turning it to "view" and turning up the output signal, listen to your solenoid buzzing or clicking so that would confirm that you have the correct pin 104.

That's no good Josh, I'm sure I used a R34 pinout when I pit it on my stagea without a problem. I still have all the diagrams I used at home some where, I'll check for you when I get home later today, I'm still in bundy. Otherwise pop round and we can compare my wiring to yours.

all good, i may have screwed up and may have read the pinout diagram wrong :lol: step 1, don't do this at night, step 2, don't let me do it :lol:

now i've lost my IEBC instructions... isn't the hand controller meant to cycle through the load points as you press the throttle? i've got the input led flashing, but not the output led flashing...

edit:

ahh crap :blink: hand controller is meant to read current load point.... mine doesn't :down: just reads point 64 like always. anyone got any ideas? i'm kinda running blind without the instructions, but google is helping a little bit...

Edited by pyro-ns

hand controller is now working and showing load point! now solenoid doesn't seem to be doing anything :) ffs!

edit: solenoid is now working! but even at idle i'm at load point 64...

Edited by pyro-ns

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 馃檹 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 馃槈. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 馃槏 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
    • I believe @Duncan has given it a crack at Mt Buller before (in actual race conditions)
    • All my Polish car culture insight comes from watching Nightride. So I half expect this to get 1UZ swapped eventually?! Are you going to drive it in winter? I'm always curious how ATTESA would hold up in the snow. There isn't that much opportunity to try it in Australia.  
    • My steering lock unit on my Infiniti G37 has failed. The car is a local 2012 Infiniti G37 (Q60 ) I need to replace the unit My local mechanic said i need to buy a complete steering wheel assembly. Does anybody no any mechanics in Gold Coast or Brisbane who can fix this issue or where i can buy just the Steering lock control unit. Thanks
  • Create New...