Jump to content
SAU Community

Save My Gt-v - Crashed!

nzboy

By nzboy,
in General Maintenance

 Share

Recommended Posts

nzboy Rookie

nzboy

Posted
Posted

so here is what happened. Driving on a rainy day on a slight downward hill and approached a mild bend at 60ks and did engine braking. Slightly tap on the accelerator hoping that I can continue my journey. Instead the car drifted and hit a light pole. Not sure if this is a write off or a repairable damage. Any ideas or thoughts. Id do anything to get this baby back up again.

IMG_0023.jpg

IMG_0018.jpg

f1192f6c.jpg

9c6449da.jpg

5410ece7.jpg

cdcabd13.jpg

heeelpppp!!!!

Link to comment
https://www.sau.com.au/forums/topic/299072-save-my-gt-v-crashed/
Share on other sites
mosquitocoils Veteran

mosquitocoils

Posted
Posted

Damn that looks bad... it looks like other than just the obvious door needing replacing, the roof needs work, and I can't really tell from the pics but do you think the rear wheel area is bent too?

payback21 Community Regular

payback21

Posted
Posted

Hmm I think you will be going to get it back on the road again. It doesn't look very good. The seal panel is mashed, the rear wheel is bent in so the rear cradle must be bend and the roof looks pretty bad too. It will take alot of work and money to get it back to how it should look.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • kevboost7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By kevboost7 · Posted

      I figured out what’s wrong. It’s something to do with the high beam wire short circuiting. When I measure the continuity with a multimeter on the headlight socket connector it gives me a continuous beeping noise when I put it on the ground socket and also on the high beam socket.  On the passenger side of the car (working side), it’s only beeping when the probe is on the ground socket. Which makes sense.  So that means it has something to do with the high beam power supply for the drivers side. How do I trace that? Is it the turn signal lever malfunctioning? The one that also controls the high beam and low beams. 
    • Bncr33nokout
      Hey lads just a fellow gtr owner

      By Bncr33nokout · Posted

      Hey lads just finished tidying up a gtr a bought. Originally from Sydney now living in New Zealand 
    • slamaa
      R33 GTR/GTS25T Rear Trunk Finisher Panel, 2-Door Models

      By slamaa · Posted

      Hi Guys, Looking for this piece if anyone can help out.   https://tfaspeed.com/products/nissan-skyline-r33-gtr-rear-trunk-finsher-panel
    • Thatjuan
      Nissan Gloria Hy34 issues

      By Thatjuan · Posted

      How did you go with your problem? End up fixing it. Have a y34 aswell vq30det
    • EndZee
      Weird compression after rebuild

      By EndZee · Posted

      But if I smoke test 5th cylinder it’s all ok, no leaks  when I try with 2nd it’s leaking exhaust and intake, it doesn’t come from oil dip stick.    so maybe when car was running poorly, rich or sth. Spark plugs were black and covered in charcoal or sth lookalike. could potential contamination make valves not seal properly? is there also a possibility that rb’s don’t have equal performing cooling passages  meaning back of the engine will be hotter than front. Can this cause improper wear if engine was running under load for short time? Or carbon build up could just burnt from 4-6 and is still on 1-3?   I out of my head like really. Timing is as manual crank-exhaust 47, exhaust-intake 38 at this point I thinking about give it a try and make another 500-1000km and check if anything change, if not I will most likely disassemble engine head /or whole engine and send it back to rebuild. It’s killing me     
×
×
  • Create New...