Jump to content
SAU Community

Recommended Posts

Have the following for sale, still on the car can see running etc, made over 300kw on 18psi with current tune, most parts are brand new and have just been fitted within the last 2 months, can buy the whole lot or will separate.

located in Adelaide

- Garrett GT35 Turbo with 0.5 front cover (faster spool then 0.7) and 0.82 rear IW & Custom Braided lines oil restrictor and custom turbo drain etc $1850

- Tune Length stainless exhaust manifold $300

- 3.5 "Bell mouth dump front pipe $350 suit gt35 IW

- 3" Silicon Hard intake pipe & Pod Filter $100

- Trust Side mount intercooler (uses short piping and goes back into stock piping) $400

- Z32 AFM with plug $250

- SARD 850cc side feed injectors with clips and loom all soldered in $850

- Yellow Jackets coil packs $300 suit r33 series 2

- Apexi Power fc + Apexi Commander with 300kw tune $1450 suit r33

- BLITZ Sbc ID3 SPEC-S Electronic Boost Controller $400

- Nismo 400r Sideskirts suit r33 $300

- Cusco Coil Overs $800

- 18" x 9.5 Dtm rush wheels stretched 235's new tyres front, 255's 1/2 tread rear $1500

- Rda slotted rotors & QFM-k750 hight temp pads $450

- Nismo Fpr $120

Edited by FOOLBOOST
  • 2 weeks later...

still got injectors,, would they fir rb20det?

yes, they are side feed so no they wont, come with collars o-rings, fuel rail, loom etc bolt in

Hey mate got 200 for the coilpacks if u will take that if so pm me cheers

Tell him hes dreamin

Are the brakes front, back or both??

Brakes are complete set of front and back discs and pads used for 2months

Hey mate, i need new coils, how do these compare to Splitfires? Obviously a fair bit cheaper so i assume they are not as good? Or is that a mistake...

Edited by nelly
Hey mate, i need new coils, how do these compare to Splitfires? Obviously a fair bit cheaper so i assume they are not as good? Or is that a mistake...

Same as Spitfires ask Performance Wise who sells them

Edited by FOOLBOOST

Xmas specials

- Garrett GT35 Turbo with 0.5 front cover (faster spool then 0.7) and 0.82 rear IW & Custom Braided lines oil restrictor and custom turbo drain etc

Also comes with new 19psi actuator, and hks alloy hard out let elbow to suit. $1700

- Trust Side mount intercooler (uses short piping and goes back into stock piping) $350

- Z32 AFM with plug $200

- SARD 850cc side feed injectors in rail with clips and loom all soldered in $750

- Yellow Jackets coil packs $280 suit r33 series 2

- Apexi Power fc + Apexi Commander with 300kw tune $1300 suit r33

- BLITZ Sbc ID3 SPEC-S Electronic Boost Controller $350

- Nismo 400r Sideskirts suit r33 $200

- Rda slotted rotors & QFM-k750 hight temp pads $400

Edited by FOOLBOOST

will the gt35 turbo bolt upto the standard manifold?

It might actually as has the smaller comp cover, havent tried it as using that low mount manifold if it didnt could always use a 10-12mm spacer. Will put more pics up today.

hey mate pic's of side skirts please?

post-31991-1261964562_thumb.jpg post-31991-1261964572_thumb.jpg post-31991-1261964582_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hmm. You're probably best off working out what the lobe centreline or even the LSA is for the stock cams, with VCT OFF. That's bound to be out there somewhere. Then, work on the assumption that the Kelford centreline is probably the same, and wouldn't be more than a couple of degrees away, if it is different at all. I'm very surprised that you needed to adjust the exhaust cam by 5° to get it on spec. That screams there's another problem somewhere. Anything from the belt being 1 tooth off (how many degrees is one tooth worth?) to simple user/measurement error on the degree wheel. I say this because Kelford, like most quality cam manufacturers these days, does a pretty good job of actually making the cams to spec, not relying on patching it up afterwards like we had to do back in the 80s.
    • Besides packing it, you can also fill your pump through the oil filter inlet port. After cranking for what felt like an eternity without pressure, i fed a tube in through there and filled it with oil. Cranked for a few seconds after that and had pressure. 
    • That's exactly what I told myself. I'm happy it came out. 
    • My bet is there's a fuse somewhere you blew that feeds power to the ECU. Or you've bumped something out behind the dash board.
    • Does anyone know what the centreline should be for the vct intake cam? On my cam spec card it just says VARI and doesn’t actually tell me what the centreline should be. I had to adjust my exhaust cam gear by about 5 degrees advanced so I’m guessing I would have to adjust my intake as well? Current intake centreline is 119 deg. Iv already asked kelford and they won’t respond, It’s the 246-A 262 cams.  thanks for the help guys 
×
×
  • Create New...