Jump to content
SAU Community

Fs: 4 X Ichiba Wheel Spacers

FoxV35
 Share

Recommended Posts

FoxV35 Rising Star

FoxV35

Posted
Posted

Up for sale is 2 pairs of Ichiba Wheel Spacers

IchibaspacersV2.jpg

Description:

Version II wheel spacers are made from Aluminum/Magnesium alloy. They are incredibly strong and very lightweight. Each wheel spacers are two pieces design with pressed studs. Now it's time to bolt-on without any swap studs hassles. These are hubcentric spacers that is specifically made to each vehicle; will fitted on your vehicle's original hub perfectly without any gap. Wheel spacers move the wheel out from the hub, effectively widening the stance of the vehicle and lowering its roll center. This simple modification increases lateral stability, which in turn provides improved handling & greater safety.

Spec:

Bolt Pattern: 5/114.3

Center Bore: 66.2

Thread: 12x1.25

Note:

Sold as two pair (4pcs) with 20pcs nuts

bought them new from US for $380 2 pairs, only used for 2 weeks before my new rims arrived. so basically it's new.

looking for $330

cheers

Image010.jpg

Image012.jpg

Image009.jpg

Link to comment
https://www.sau.com.au/forums/topic/300357-fs-4-x-ichiba-wheel-spacers/
Share on other sites
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Nismo coppermix twinplate clutch

      By joshuaho96 · Posted

      No, with a twin plate clutch flywheels and clutch pressure plate/friction disks go together. Only clutch where that isn't the case is the Uniclutch but they currently don't make a pull version for the Getrag R34, just some other cars. Personally the flywheel is as light as I'd want it to be. It already drops revs faster than I want to shift normally and I blip the throttle again to rev match on upshifts.
    • The Skyline Guy r34
      Nismo coppermix twinplate clutch

      By The Skyline Guy r34 · Posted

      Are there any other lighter flywheels that can be used with nismo coppermix twinplate system? Id like to gave the revs pick up faster than oem
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      RB20/25 covers don’t have threaded fasteners stock like RB26 covers. They are blind rivets so I will need to drill out and tap threads. I bought some M4x6mm button heads and will report back once done if I chose correctly length wise.    have also got some loctite 
    • MBS206
      R32 update from 1990's spec.

      By MBS206 · Posted

      Interesting. I've not dived into the cleanliness of the factory CAS. I'm curious if the variations are less of an issue if the OEM sensor were brand new. Optical sensors if they're starting to get dirt and crap into them as they're getting older would definitely cause issues as they age.   It's an interesting point to keep in the back of mind for me though
    • GTSBoy
      High temp brake fluid?

      By GTSBoy · Posted

      Hmm. Tough one. Without knowing where the conductivity value is supposed to sit, it's hard to know whether a standard DMM set to an available ohms setting would be able to measure anything. Ohms being the inverse of what we're talkng about and probably good enough for the girls I go out with. But if you want to go all hoity toity with a 4 wire rig - go ahead. It can only be more accurate - just in case more accuracy or repeatability turns out to be required. If you're going to the effort, just go chuck the ohm-mage probes into the car's reservoir and see if you can measure anything at all?
×
×
  • Create New...