Jump to content
SAU Community

Neo Rb25det Vct + Bigger Cams

JDM_Spirit

By JDM_Spirit,
in Engines & Forced Induction

 Share

Recommended Posts

JDM_Spirit Community Regular

JDM_Spirit

Posted
Posted

Hey everyone,

Ive been making plans for abit of a big project and been scratching me head about something.

Im planning on using a Neo RB25DET head and retain the VCT.

One of the many options are to add some aftermarket cams into the package.

We have seen a S2 RB25DET on the dyno with factory Cams and VCT and by shifting the VCT's cut off point

etc, we were able to get better torque figures.

The owner then added Step 1 Cams and didnt utilise VCT and similar results were made, therefore no real

gain was made.

Now what I was wondering was, how big can I go before VCT can no longer be used nor functional?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/300450-neo-rb25det-vct-bigger-cams/
Share on other sites
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Bang for buck ...more boost is the answer. get your turbo highflowed or get a GT3076 or suchlike and a decent tune ( you will need a nistune in your ecu). that will enable you to play with the vct changeover points but I doubt you will see dramatic or any improvements from that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Import insurance in 2025

      By Kinkstaah · Posted

      The max they would go for me is 50.
    • Duncan
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By Duncan · Posted

      That cannot have been a fun set of drilling. The stock "baffle" looks identical to rb26, I just cut fuel cell foam to fit the full length under the baffle.
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

    • GTSBoy
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By GTSBoy · Posted

      I understand your sarcastic exasperation. But to be fair - the baffles do indeed fit OEM cam covers. They did omit to say that you need to do a bunch of stuff. But they do fit them.
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Got started on the modification to make these splash plates fit over the long weekend. First the surprisingly time consuming task of swapping all the cam cap bolts to Tomei cam cap studs. I did the method of removing one bolt at a time, applying loctite to the stud, double nutting to torque as the manual described. Then carefully unlocking the nuts without disrupting the torque of the stud (and going back to re-torque a few times when it slipped). Finally applying the nut and torquing to spec. Repeat x28 Next up I went about removing the stock cam cover baffle so I could ensure it was fully clean after drilling for stud clearance.  As the blind rivets holding the baffle on were domed I used a punch to mark the center then used 4mm drill bit to carefully drill out the rivet without going too far part the baffle. As seen in other thread here is what is inside the stock baffles I decided on M4x6mm bolts to bolt the baffle plate back on with. I used a 3.3mm drill bit with some tape to mark the depth at ~8mm. Next was to tap the threads using a cheap bunnings kit M4x0.7. With the baffle removed I also drilled out the spot welds holding in the baffle plate oil returns. Unsure whether this was the best option or if I should have cut holes in the Hypertune splash plates to allow the oil drains to still function... time will tell. I then removed the the Hypertune splash plates so I could rest the cam cover on top and use a dab of grease to mark where the studs impacted the oem cam cover baffle. The most obvious spot was on the hump from the stock mesh is held. Using this hole as an anchor I bolted the oem baffle plate back into the cam cover and lined up the Hypertune splash plate. Marked the rest of the holes for the studs and drill those out too. Total 32 holes drilled and 12 threads tapped on the passenger side cam cover alone for this bolt on part that totally clears all OEM cam covers.. Drivers side next as well as some E85 safe fuel foam to fill the space behind the behind cam cover baffle plates. oh and some lock nuts for the splash plates of course.
×
×
  • Create New...