Jump to content
SAU Community

Recommended Posts

I have noticed sometimes the fuel gauge in my car drops from 1/4 tank to empty with the light on, in the space of a few k's. I read the v35's are having similar issues and wanted to know if anyone else has this problem.

I pulled the pump out to check but couldn't find anything obvious wrong with the sender resister.

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/
Share on other sites

In the space of how many km's Scott?

Mine goes from 1/4 to light on after ~140kms normal driving :)

or

1/4 to light on after ~70-80kms of fun driving

I have noticed at times that the light will be on when I shut the car down, then an hour or so later when I go out again I will have just over 1/8 of tank left with no light on (nor does it come on for a while either).

Can also behave differently on different fuels.... Vpower will drop from 1/4 to nothing much faster than Ultimate.... and don't get me started on Vortex98 :ninja:

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-4991205
Share on other sites

Mine fluctuates the whole time, not just below the 1/4 mark. It can be below the 3/4 mark and then 5 minutes later its showing just above it...

I've learnt not to pay that much attention to it - since its usually just a "rough indication" rather than an accurate measurement.

Lately I filled up when the needle was just above empty (as in very very close to the empty line), but only got 54L in. Other times its been on the empty mark and I've managed to get around 62+L in.

From 1/4 to empty I normally get around 50-80km maximum.

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-4991263
Share on other sites

It goes down fast at the end of the tank and probably does exactly the same thing. I am not that worried as I just fill up when the light comes on.

Cheers

Andy

I tend to not pay attention to light unless i am over 400km's in that tank haha.

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-4991559
Share on other sites

Mine drops to light on sometimes after one boot onto the freeway then stays there. If I switch the ignition off and on, its back up to where it was.

Im guessing there is a dry solder joint there somewhere, anyone know where the electronics is for the sensor? Let me guess, dash out?

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-4992088
Share on other sites

  • 1 month later...

Lately my fuel gauge has been getting much worse. Rather than giving me a pretty close "ballpark" reading, its now often wildly inaccurate. I've seen it nearly at the half way mark after just 130km or so, then I'll actually manage somewhere near 200km before it goes below the half way mark, then later it could be back up between 1/2 and 3/4...its just all over the place, often out by more than 1/4 of a tank!

Not sure if its just a faulty sensor but its very annoying. Soon I'll be using the kms since last fuel stop to determine how much fuel is in the tank...on a 2003 model car!!

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5056072
Share on other sites

Lately my fuel gauge has been getting much worse. Rather than giving me a pretty close "ballpark" reading, its now often wildly inaccurate. I've seen it nearly at the half way mark after just 130km or so, then I'll actually manage somewhere near 200km before it goes below the half way mark, then later it could be back up between 1/2 and 3/4...its just all over the place, often out by more than 1/4 of a tank!

Not sure if its just a faulty sensor but its very annoying. Soon I'll be using the kms since last fuel stop to determine how much fuel is in the tank...on a 2003 model car!!

I sometimes get that, seems to be the carbon on the sensor wearing out as I pulled it out for a look. If you switch the ignition off and on, it goes back up to where it should be.

I wonder if you can buy the liquid carbon and repaint it...

Edited by scotty nm35
Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5056387
Share on other sites

after fixing my turbo pressure pipe. i have been clocking 500km's easily in the volvo..

and this is with the same thirsty driving i was doing when i was getting 400's if not more pedal now i have more boost :)

?? what pipe is that?

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5057959
Share on other sites

rubber hose near washer bottle to plenum area..

You mean the one that goes to the boost sensor (ie. the sensor in the little oval shaped black box that sends the boost readout to the in-dash guage) ?

Interesting, I fixed that sensor a few months ago after reading how to do it on here (power connections inside it needed re-soldering) but at the same time the factory hose split and continued to split every time i cut it and re-attached it...so I've replaced it with a similar sized hose but this one keeps falling off the plenum side since there's no "lip" to hold it on. Its been bothering me in the back of my mind ever since (ie. vacuum hose off cant be good) but I just haven't gotten around to fixing it since it didn't seem to upset performance.

Now that you mention it the fuel economy could well have started to go bad around the time I fixed that sensor...was getting mid 12's (L/100km) and now its consistently in the high 13's if not low 14's... :P

If thats all it is then I feel a bit silly for leaving it so long...

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5060142
Share on other sites

Im guessing Angus means the 60mm black rubber pipe with the bend next to the washer bottle.

The hose you are talking about, the 3 or 4mm one will need to be replaced on most of the M35's coming in as they are very brittle. It only affects the boost meter in the dash so im not even sure all M35's have it. Definitely wont be the source of your bad economy, probably the heat doing that as the ecu is adding fuel as the inlet temps go up I think.

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5060484
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...