Jump to content
SAU Community

Recommended Posts

Spotted a silver R32 GT-R V-Spec II with the factory (I think?) BBS wheels and everything down parked in front of Weston Creek Indoor Sports Centre about 7:30/5 mins ago

beaddiful car, I thought Jayce's was the only one in town

Yep;know that car! There's actually a third V Spec II in town(that I know of-I s'pose there may be more),but yes,there ain't many of "us" about!

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/259/#findComment-1824169
Share on other sites

spotted a white supra today near Lanyon, black carbon fibre bonnet, big wing and black flame decals up the side. looked like something out of the F&F. still, pretty cool, got my attention!

Also a yellow R34 GT-T heading towards tuggers along Athlon.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/259/#findComment-1829897
Share on other sites

Termainal: wasnt me.....

LO_R33: i was filming that for the news that night and did a live cross from outside one the houses which were burnt down. poor buggers.....

Damn man, did you beat the firetrucks there? Win news beat the fire trucks to the scene by atleast 15 minutes... :) Maybe news crews should start carrying big water pistols :lol:

Was pretty scary how quick that fire came from a small grass fire, to an out of control mess.

Dayne

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/259/#findComment-1831320
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • 1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
    • How does this compare to the internally gated g25-550 in terms of power production at same psi and spool
×
×
  • Create New...