Jump to content
SAU Community

Recommended Posts

I was there tonight, black 33, might have been me if it was around 9.30-10ish?

Thats the one..! You may have seen me.. I was in the car with chicks spreading themselves all over the car, people wanting to know me, taking pictures, sponsors wanting to pay me $$$ to put their sticker on my car. "I aint commercial BIATCHES!"

No.. I was in my dads camry... :P

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2869114
Share on other sites

Spotted a silver series 2 R33 driving down belconnen way last night around 5pm, TALKING ON HIS PHONE. I wish people would stop talking on their phones while driving, especially Skylines, it gives us a bad name.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2870140
Share on other sites

Think i saw mivec. maroon 33 with the same kit. Going along parkway around 1ish yesterday. Very nice car. I was in the white 33 sedan.

What time? I was only out and about at roughly 930 or 130ish

I did see a white 33 but I don't think it was yesterday, maybe the day before when I went out to take piccies of teh car.

Edited by MIVEC
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2870808
Share on other sites

Thats the one..! You may have seen me.. I was in the car with chicks spreading themselves all over the car, people wanting to know me, taking pictures, sponsors wanting to pay me $$$ to put their sticker on my car. "I aint commercial BIATCHES!"

No.. I was in my dads camry... :P

:)

i need to get me a camry!!!

;)

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2872759
Share on other sites

Tool in Sydney rocked pretty f**kin hard aswell :laugh:

tool2.jpg

HAR! I am master pit photographer!

saw tool at bdo in melbourne and also their sideshow in sydney at which i went backstage to hang out with adam afterwards ha!!!

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2873971
Share on other sites

saw tool at bdo in melbourne

My mate saw them at BDO melbourne and at the Sidney Myer Music Bowl. Apparently BDO blew goats, you could hardly hear maynard at all. Not to mention it was a Festival, and that is of course a dirty dirty place of worship.

December, maybe November

*dances*

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2874174
Share on other sites

That was me! Damn those wheels on your car look wide. I like :)

thx

I like the wheels, I am getting sick of the colour though, Don't know which colour to choose atm, wish they hadn't been powdercoated gold :)

Edited by CeJay
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2874697
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Is it a dog or synchro box? I guess either way, if it is new and crunching in one gear only, it has to come out and go back to the shop to check/measure as there is either an assembly or manufacturing issue
    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
×
×
  • Create New...