Jump to content
SAU Community

Recommended Posts

saw a white R32 leaving fyshwick at about 5pm and a falcon ute hit the back of a truck on townsville street at about 12pm, did a good job of wrecking the front of it!

that was me. the 32 that is, not the ute. woah, i haven't been on here for yonks.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/453/#findComment-3518617
Share on other sites

spotted friggin WRX's... everywhere! don't know why, but I just seemed to be constantly surrounded by them today!

spotted a black R32 going past Babar tonight

a purple R33 at Drakeford/Athlon intersection, and was also behind a white R31 with 3 digit plates at the same intersection.

oh and there's always a grey R31 with R31 Club sticker near my house but today there was a 2-tone 4-door R33 there as well (Kambah).

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/453/#findComment-3520237
Share on other sites

saw LadyBytes out at the hill climb yesterday as well, looks like fun! and also saw a maroon r33 with chromes at the cotter yesterday arvo at round 4

I saw your car come in and didn't see you get out or know who you were... you should have come and said hello :P

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/453/#findComment-3524653
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was roughly 3.5 hours.    car went in around 11:00 and I was done around 2:30 He did the initial runs, install the BC and then Nistune install and tune.  The best part was sitting in the lobby and hearing the skyline on full throttle at the dyno 😂😂
    • Glad it all went smooth. How long did the tuning process take?
    • Yeah that was kind of the same feedback my tuner gave me.  the boost tee is until I can sort out my plan for the electronic boost controller and what I’d get, where I’d mount the dash etc.  I’m happy with this until I can figure it out. Not a big fan of the A-pillar gauges. I’d like to get a clean install of the boost gauge - something digital like GFB.  Something like that might fit neatly where the ashtray is and look clean. I feel like replacing the OEM triple gauge is a bit extreme for a weekender like my skyline. And it’s not making crazy power to need all the additional sensors/gauges. 
    • I'm about to swap my box to Tremec T56 Magnum F & initially thinking of re-using my DCS twin plate (can get it re centred for the bigger spline) but it's been called out the box will be noisy (rattle) as the clutch is unsprung.  So I'm doing as much research as possible. I'm not so worried about holding the power as I'll go the track version which on paper will hold the maybe 1000hp I make. It's the longevity I worry about. DCS told me they don't use a sprung centre as it's just something that can break. The uni clutch has a very complicated sprung centre. Any one had or heard about any issues with it failing? Thanks in advance.
    • Auto is at least 10% (from my real, actual experience with different torque converters and manual on the same setup) ~185rwkw at 11.6psi (peak!) is entirely what one would expect without a FMIC or anything else on the intake, it does bleed off towards the higher RPM so it's what, 9psi there? Note: There is nothing that can be done about this with a manual boost tee. If you want to hold it steady and gain more top end, well - You will need electronic boost control.....
×
×
  • Create New...