Jump to content
SAU Community

Recommended Posts

spotted a maroon r32 with FMIC in belco at lunch timish.

spotted a silver R33 with wrx bonnet scoop, huge front bar with mesh grill and mesh infront of the FMIC, 20" zenetti masqerades, standard rear bar? with huge angled upward "imfullawater" cannon on the back. not my taste but didnt sound to bad

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/668/#findComment-5834686
Share on other sites

spotted a maroon r32 with FMIC in belco at lunch timish.

spotted a silver R33 with wrx bonnet scoop, huge front bar with mesh grill and mesh infront of the FMIC, 20" zenetti masqerades, standard rear bar? with huge angled upward "imfullawater" cannon on the back. not my taste but didnt sound to bad

I saw that last weekend in Tuggers.....definitely got a chuckle out of me when I saw it.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/668/#findComment-5834793
Share on other sites

Think I spotted Jimmy's yellow beast on Gungahlin drive followed by a black R33 just after 5 this afternoon. Was heading in the opposite direction in the little coupe :)

Yeah got out of work a bit later than usual.

i think you're one of the few people that actually notices me getting around.

i still haven't spotted your coupe yet though.

you must be a ninja :ninja:

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/668/#findComment-5835707
Share on other sites

Spotted a 300zx pulling over on drake-brockman dr this morning, then the driver getting out of the car as i drove past.

Engine out.

haha exactly what i was thinking as i scrolled down.

saw a silver R33 with GTR badge but didnt look like a GTR wing on hindmarsh southbound about 5

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/668/#findComment-5836440
Share on other sites

It'll be home within 2 weeks.

This is the second longest time it's ever been off the road in 5 and a half years and I think this is going to be the most worthwhile.

Pffft snapped, he drives a 33 and a hair dressers car :nyaanyaa:

Ahahahaha oh Kat, don't you know a hair dressers car can't have more than two doors! :P

$10 says your car is back in a shop of some sought within 6 months :P

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/668/#findComment-5836459
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This piece is obscenely discontinued. I honestly hate the frameless window design because the rubber gets stressed and the guides as well every time you open and close the door.
    • I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
×
×
  • Create New...