Jump to content
SAU Community

Recommended Posts

Spotted Trozzle's car parked on the road out the front of Gentech in mitchell yesterday arvo

Yerp, was getting engineer's certificate at Canberra Motor Works. Unfortunately didn't get it due to a few things (one of which is worrying lol), however shouldn't be hard to fix up. Unfortunately I foresee having to cancel the rego on my car before the lack of defect clearance does it.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/720/#findComment-6250315
Share on other sites

Something to do with the diff/cradle mounts is allowing the whole diff to move up/down around 10mm

Yeah you're right.. just a little worrying :/

Spotted Troy and Richard hugging each other as the sun went down over the lake. They looked to be eating takeaway.

Hope you boys had fun

Sin and his troy boy

ultra-gay.png

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/720/#findComment-6250393
Share on other sites

Spotted Troy and Richard hugging each other as the sun went down over the lake. They looked to be eating takeaway.

Hope you boys had fun

Sin and his troy boy

Batted Savs with Mayo & Choc tipped Bannanas, your Favourites. You should've come............

Gags :sick:

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/720/#findComment-6250489
Share on other sites

Cheers Josh!

Yours had a nice tune when it took off as well

I spotted a r31 parked outside of Pedders in Phillip as I dropped my car off for an inspection

Spoke to the guy who owns it about his Rims dont know if his online here

Also spotted a Silver 33 cruising around Phillip.

Then Josh rocked up for a surprise visit just after I talked to Natrad about my constant coolant problems

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/720/#findComment-6253128
Share on other sites

Pedders bad :down:

Rear calipers installed on wrong side and upside down. Pads on wrong way in calipers.

All new suspension installed but not adjusted. Camber out, toe out, F/R balance alignement out.

Bled in wrong order, air in brake system. Did not and would not blead ABS - WTF.

3 x returned for fixing - no luck and they had no idea.

Sir your brand new Rotors/Calipers/Pads/braided brake lines/BMC have no problems. Your car just does not stop very well and its got very spongey brakes. You should look on the internet and see what you can do to fix that !!!!!

Yes I went back and told them what was wrong and that I had paid again to have it done.

1 minute at ACT brakes - your calipers are on upside down and wrong side sir. Fixed. Felt alot better.

But these guys didnt notice pads installed correctly. Went back twice more. Sir there is nothing more we can do !!

Both of the above shops have "Brake Specialists" in their business name.

ESP identified and resolved all brake issues :thumbsup: and bled the ABS as per what you are supposed to do !

Capital steering and suspension for dialing in suspension :thumbsup: . Booked in Wednesday.

I should go get the spare key to my car and go steal it back haha?

Okay well there goes $14 for the inspection lets see what they come up with that's wrong with my car

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/720/#findComment-6253190
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You shouldn't need to massively fatten up the mixtures for cold conditions. For one thing - 0°C is not that cold. For another, the Haltech will be using the IAT sensor to tell it how dense the air air, and calculate the correct amount of fuelling. Then the cold start enrichment is added as a % on top of that, so it should scale with the main fuelling. You might also doubt the IAT sensor at this time. You're not using one from an RB26 are you? Using a nice Bosch sensor or similar? Happens. Some wideband units take great pleasure in killing their sensors. Put another wideband in the tailpipe and compare. Or just swap the sensor to a brand new one and see.
    • Oh, my misunderstand. When the car was running, it sounded ok, but if I gave it any gas it wanted to die but caught itself afterwards. It's very different from how it was a couple months ago when it was warmer outside. The logs show that the AFRs are better during, what I assume, is warmup enrichment. Because it's cold, and air is more dense, should I work on the enrichment bit?
    • yess of course im not using 2nd hand parts from my spare engine, but the place where i live is hard to find parts for the RB20DET ,but for the RB20E is everywhere including new ones and a lot cheaper ,because for the RB20DET you have to order it overseas to get one and it cost a lot of money 3x the price to be exact. so i ask this topic because if i can use the new ones but for RB20E is it compatible or not. if not im screwed haha, not totally screwed but i have to save a lot of money first before i can begin repairing my engine, thanks for the information before.
    • Unless my sensor just died, was only a couple months old, I strongly believe it didn't. How can I test it? I never mentioned it being 20:1+?
    • Well, you wouldn't use 2nd hand bearings out of another engine anyway....so just buying the proper bearings is obviously what you're going to do. The crankshaft would be common. The conrods might be common. There is essentially nothing else you would be able to use.
×
×
  • Create New...