Jump to content
SAU Community

Recommended Posts

There was actually one for sale somewhere on here.. It was fairly cheap too

edit: http://www.skylinesaustralia.com/forums/topic/436977-r30-skyline/

$1000..

I'll go halvsies with someone? ;)

Edited by dontyellpl0x
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/920/#findComment-7173354
Share on other sites

The ARK is going to have to wait... But I wish. :rolleyes:

There would've likely been Jap versions too but I've mostly only seen Coupe or 4door sedans and not hatches.

dr30-1.jpgDR30-rst.jpgab32a0df.jpg

dr30-1.jpg

4517428233_b705468fc1_o.jpg

This R34 ^^^ Looks MAD! and I love the Wagon too. :P

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/920/#findComment-7173392
Share on other sites

That silver thing is faaaaarkn nice ... (even with four handles) .. the 34!, well that just goes without saying .. :P

Have been thinking of dropping the wing, it looks good .. but then there's the 'tradition' thing goin on with my wing, it's always a debate within my mind. ;)

Edited by THE34T
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/920/#findComment-7173546
Share on other sites

Get a spare bootlid without the wing and chop and change.

If you no like, flip it back. :D

Tradition Schmadishion.

which reminds me... I really should try get around to getting my spare bootlid with wing painted. :yes:

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/920/#findComment-7173551
Share on other sites

Silver R33 S2 with P plate, R34 GT rims and a big scar down the drivers side at Charnie shops Lunchtime-ish. Greetings were swapped thru open windows.

(I was in the 33)

Parked next to a Silver StageA AR-X 4 at Charnie shops around 6pm.

(I was in the SkyWagon)

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/920/#findComment-7174067
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • does anyone know tie rod torque setting and anti roll bar for r34? Is there a workshop which shows various components torque setting?
    • Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
×
×
  • Create New...