Jump to content
SAU Community

Gtr Injector Ballast Resistor

Ganador

By Ganador,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

Ganador Enthusiast

Ganador

Posted
Posted

Got a s13 with a 26 conversion and removing the motor yesterday. As i went to unplug the resistor pack all the spade plugs that they had used to connect the resistor ended up coming out.

Now i know the resistor has 7 wires. 1 12volt ign and 6 wires for the injectors. All wires are black so i can test for the power wire. Question is, am i able to just put the plugs back in any format or do i need to match the wires from the resistor to the injector?

Link to comment
Share on other sites
winstonusmc Enthusiast

winstonusmc

Posted
Posted (edited)

It looks like pin 3 is the power in. It doesnt matter what injector goes to what though, just as long as power in is pin three. The diagram is as you were looking into the back of the harness side not the resistor side.

post-44642-1261532089_thumb.jpg

Edited by winstonusmc
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      Hello, I am looking to replace my two rear drive shafts in my R34 N/A Skyline but I'm finding conflicting information. Do S13/S14/S15 or R32 NA/ R33 NA fit? https://justjap.com/products/gsp-premium-rear-drive-shaft-l-h-nissan-silvia-s13-s14-s15-3x2-type?currency=AUD&srsltid=AfmBOoqY7EwDaYCUoUU3mxxZ_qrUXkVVHiV4MIN7ozoar6scjnEiekv- would this fit?
    • Butters
      Uniclutch pull type clutch

      By Butters · Posted

      Hoping they release an R34 getrag pull type.  
    • Dose Pipe Sutututu
      GReddy Injector Help!

      By Dose Pipe Sutututu · Posted

      You need the bottom spacers, to make it a 3/4 height injector. https://www.efihardware.com/products/3040/injector-adapter-lower-for-extended-nose-injectors   And you'll need to buy the right injector bosses, these "might" fit. You'll need to measure it up. https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/  
    • GTSBoy
      GReddy Injector Help!

      By GTSBoy · Posted

      Unless there's something particular about the Greddy manifold's injector holes that I'm not aware of, those injetcors look to be totally wrong. They would absolutely want to be spaced up to get those long snouts out of the runner. Which, I think, is not usually the way that that problem is solved. I think the problem is solved by using the correct injectors, which would be much more like what Andrew posted.
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Thanks for the reply, So i've continued playing around, and fitted the injector adaptors onto the injector, the fuel rail is not able to be mounted now as the injectors sit a bit further out. I suppose the point of the adaptors is so that the injector nozzle isn't so deep into the intake? I suppose 1mm extra on the o-ring would do it but still can't mount the rail onto the intake haha. Waiting on a reply from Aeroflow I'm sure there's something stupid that I'm missing...
×
×
  • Create New...