Jump to content
SAU Community

R32 Gtr Rb26dett Block, New Welsh Plugs, Squirters And Cradle

sebastion
 Share

Recommended Posts

sebastion Proficient

sebastion

Posted
Posted (edited)

hey guys, we have a r32 rb26 block for sale, has new welsh plugs, is in good condition, not warped or cracked etc, was only replaced due to slight scoring in the back 3 cylinders... please refer to the pictures, and dont mistake the staining on the surface of the bores as scoring... block will come with its cradle, and also comes with all 6 squirters in perfect order... please note current bore is 87, and would suit being bored to 87.5mm (the largest relatively safe bore)... as for a price, we are after $550ono for it, may consider swapping it for any parts of intrest, otherwise cash in hand upon delivery... we can deliver between lismore NSW and brisbane QLD if we get the money we are after for it. also please, we are NO WHERE near SYDNEY..... thanks

cheers guys

post-56395-12561743833347_thumb.jpg

post-56395-12561744305443_thumb.jpg

post-56395-12561746141149_thumb.jpg

post-56395-12561746466433_thumb.jpg

post-56395-12561746781877_thumb.jpg

post-56395-12561747487653_thumb.jpg

post-56395-12561748159392_thumb.jpg

post-56395-12561748682554_thumb.jpg

post-56395-12561749258883_thumb.jpg

Edited by sebastion
sebastion Proficient

sebastion

Posted
  • Author
Posted

we do have another block, it has been freshly bored out 20thou, decked and honed, has not had any use since... needs welsh plugs... after $800 for the block as it is bare (comes with matching cradle of course) (new ones sell for $1500+) either way one of these need to go, have not got enough room, and we are moving in 2 months time...

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      BCNR33/ECR33 Door corner piece replacement

      By joshuaho96 · Posted

      This piece is obscenely discontinued. I honestly hate the frameless window design because the rubber gets stressed and the guides as well every time you open and close the door.
    • jacobzking
      Feedback on these “rebuilt” Nismo injectors

      By jacobzking · Posted

      Thank you!
    • Duncan
      Feedback on these “rebuilt” Nismo injectors

      By Duncan · Posted

      I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • jacobzking
      Feedback on these “rebuilt” Nismo injectors

      By jacobzking · Posted

      I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
×
×
  • Create New...