Jump to content
SAU Community

So I Understeered And Smack Bang Hit The Gutter

IM-32-FK

By IM-32-FK,
in General Maintenance

 Share

Recommended Posts

IM-32-FK Mentor

IM-32-FK

Posted
Posted (edited)

Alright so for the most of you living in sydney, you know it was raining all day today....well i was going in a roundabout and the car understeer(i was going about 40km/h) and because of this, my car locked up and i hit the gutter with my left front tyre. After having a look at it, i can see the tinrod(the bottom metal bar in the inside of your wheel) is snapped and the whole rim shifted back and is touching the guard, so basically, the tyre is not being pulled foward!!!when i drive it and turn left even slight, the tyre hits the guard and it makes a 'rubbing' sound.

i was wondering if this is a major problem and if it will set me back alot (the car is a 93 r32 gts(non turbo)) and if the parts are hard to get and where i can get it from in sydney.

thanks

Edited by IM-32-FK
mad082 Grand Master

mad082

Posted
Posted

if it is simply the tie rod or steering arm being damaged just buy a new one, install it then take it to get a wheel alignment (or get it installed by the place doing the wheel alignment.

i think you would be best of taking to a steering place and letting them do it so that they can check it all over and make sure nothing else is damaged

Yme33 Enthusiast

Yme33

Posted
Posted

same as Mad082 take it to a steering place worse off you could have bent the subframe a lil, the steering mob will find that out and can put it on a jig to straighten it, hope it is only the tie rod and nothing else if so easy to replace and get a wheel alignment after it done.

IM-32-FK Mentor

IM-32-FK

Posted
  • Author
Posted
same as Mad082 take it to a steering place worse off you could have bent the subframe a lil, the steering mob will find that out and can put it on a jig to straighten it, hope it is only the tie rod and nothing else if so easy to replace and get a wheel alignment after it done.

i had a look at it today and i can see the tie arm is snapped and the lower chamber arm is a bit bent...the tie rod seems fine...i also noticed the shock wasnt 100% straight too :D

honestly, how the hell am i going to take it to a wheel shop when i can bearly drive it...

astrotristan Grand Master

astrotristan

Posted
Posted

just get a tow man, racq do them free for the first 10km or something, and then its pretty reasonable after that :D

thats what i did when i snapped my rear control arm in the 32

IM-32-FK Mentor

IM-32-FK

Posted
  • Author
Posted
just get a tow man, racq do them free for the first 10km or something, and then its pretty reasonable after that :D

thats what i did when i snapped my rear control arm in the 32

racq? so a company will prodly tow your car for free for the first 10km even though u never did any business with them?whats the catch?

astrotristan Grand Master

astrotristan

Posted
Posted
racq? so a company will prodly tow your car for free for the first 10km even though u never did any business with them?whats the catch?

sorry bro i just realised you live in nsw - im pretty sure racq is just qld

basically u pay $50 a year and you get 24/7 roadside assistance, whether it be for a flat battery or whatever

but yeh you can get unlimited tows (provided you have reason) and the first 10km are free

last year i got 4 tows in total, 1 lower control arm, 1 for thermostat going, 1 for radiator going, 1 for cooler piping f**king up

well worth $50 :D

NZM.031 Grand Master

NZM.031

Posted
Posted

to take a hit like that you have to be fair hooking.. i know, because ive done the same.. slightly damp day.. wierd off camber right hander.. bald rear tyres, front tyres down on pressure, came in too fast, and in to the gutter she went. i used ratchet straps to pull the front wheel forwards enough to drive it on the trailer. have a good look at your tie rod as they bend with a slight touch. also the end of your crossmember can bend easily... it is all designed to snap and crumble like this so it doesnt transfer the shock to the chassis... bent chassis = wrecked car.

the parts are out there... you just have to be on the lookout. if you need it going asap its going to be expensive though.

you were going faster than 40km/h... at 40km you wouldnt do that much damage.. 60km/hr maybe.

32_Dave Mentor

32_Dave

Posted
Posted
i had a look at it today and i can see the tie arm is snapped and the lower chamber arm is a bit bent...the tie rod seems fine...i also noticed the shock wasnt 100% straight too :D

honestly, how the hell am i going to take it to a wheel shop when i can bearly drive it...

find replacement parts, is time consuming but a piece of cake.

lower LCA for passenger side

stock shock for passenger side - if there stock

Passenger side tie rod.

if you were in qld i could of helped you out with all of it.

Best of luck man its quite easy to find this gear. Troll the parts for sale section in NSW or the main section.

32_Dave Mentor

32_Dave

Posted
Posted
to take a hit like that you have to be fair hooking.. i know, because ive done the same.. slightly damp day.. wierd off camber right hander.. bald rear tyres, front tyres down on pressure, came in too fast, and in to the gutter she went. i used ratchet straps to pull the front wheel forwards enough to drive it on the trailer. have a good look at your tie rod as they bend with a slight touch. also the end of your crossmember can bend easily... it is all designed to snap and crumble like this so it doesnt transfer the shock to the chassis... bent chassis = wrecked car.

the parts are out there... you just have to be on the lookout. if you need it going asap its going to be expensive though.

you were going faster than 40km/h... at 40km you wouldnt do that much damage.. 60km/hr maybe.

does it matter what speed he was doing? lets give him a hand and help him out.

mate ill have a look here what i got, weight it and give you an approx on price / post for above parts i listed. drop me a pm with a post code.

dave

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      Diagnosing with and without is mostly the same. You need to know, as Duncan asked, and what conditions. Car hot, cold, idling, driving, if while driving what rpms, is when you're varying, or is it when held constant.   From there it's understanding what can be causing it. Starting with pretending all of the sensors are correct. Which means if it's going rich, why would it be thinking more air is going in than it is, and under what conditions. So things like if only when under boost, it could be be a loose intake piping joint. It's just understanding the system, and understanding when/how the problem occurs, and then if it's only occuring in specific scenarios, what can be causing it.   ECU specifically, if it's aftermarket, it'll have software you can use, for the Skylines on factory ECU, there is Nissan Consult you can use. Most ECUs have a way to get data from them.
    • silviaz
      R32gtr sputtering and stalling

      By silviaz · Posted

      How do you go about diagnosing ecu's that don't have data logging, is it more experience at that point and just trying out things that you think will fix the issue?
    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      Stock O2 are basically useless beyond anything at stoich. Any misfire will also be seen as lean. The stock O2 also read a collective exhaust gas volume, not each cylinder. Sputtering and missing means not each cycle is firing, and some are. Which means even if rich, as shit, on cylinders as they miss, they'll read lean, but the cylinders that did fire will read rich, and combined, well, they can read anything from rich to lean.   Start with the basics before even going looking at sensor values.   Edit: I say the above, and that's coming from the guy with a few thousand dollars worth of scan tools sitting right beside me right now that I use frequently for my job.
    • sk8boy204
      Auto GTS4/Stagea transfer case.

      By sk8boy204 · Posted

      I just finished up a manual swap and I have a 1999 S2 AWD automatic in my garage, depending on where you are located. I'm in the the midwest of the US.
    • r32-25t
      R33 GTR N1 REO on an r32 ?

      By r32-25t · Posted

      I’ve heard it can be done, you need to redrill the holes where they bolt to the chassis and apart from that they are the same. I’ve never done it or know anyone personally that has, it’s just something I’ve heard 
×
×
  • Create New...