Jump to content
SAU Community

Recommended Posts

  • Replies 521
  • Created
  • Last Reply

Top Posters In This Topic

f**k yea, 104 in a 60 zone :3some: i was gonna go for a run but it was a pusute car so i thought i better not, but the cop was ok, he said he saw me in the 80 zone when clearly was not but i wasnt gonna argue with that... $210, oh well, paid it about 20mins after so its all good

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/22/#findComment-3053823
Share on other sites

well found out in the last two days im either comin back up there or too brissy at the end of the year my job prob wont be here at the end of the year, so the sinista plates may grace my car once again, this time i will be back with avengence (hmmmm 320odd rwkw) hahahaha i have to wait to find out lol

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/22/#findComment-3063704
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Hey ill be in Darwin from 21st of June to 3rd July.

How about a cruise on the 30th so i can have a look at some Darwin Skylines???

I can participate in the cruise in either a 4wd or Hyundai! (Dont judge me, its not my fault) LOL

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/22/#findComment-3134954
Share on other sites

if you want that , you will have to post in the NT section of Boostcrusing.com , as there are not enough skylines to keep this part of this site running , there are some very nice lines up here so I hope it happens

Cheers

Jaqule

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/22/#findComment-3136793
Share on other sites

26 the 31 Zac, pron!

I have thought about it but its a bit of work... was guoing to do a 25 because they're not so much work. But looks like i could have another RB30 soon, and it wont cost me jack so i'l probaly do a crazy RB30. :sorcerer:

Link to comment
https://www.sau.com.au/forums/topic/30197-darwin/page/22/#findComment-3153920
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hey all, I'm working on a project car and I believe I made some mistakes. I'm looking to remove the clear coat from my car on most panels (except for panels where the paint has blistered, I will sand this), but wanted to know if these steps are correct?   1) Get a red scuff pad (abrasive one) instead of sand paper to remove the shine from the surface 2) get 400 grit sand paper and go over the entire car with a random orbital sander so the surface is smooth and the primer can grab onto something 3) On the blistered paint, go over it with around 120 grit sand paper, go to 240 to smooth out the scratches, then finish on 400 grit. Anything to add in here or any feedback?
    • Agreed, another vote for the Haltech CAN wideband.  No voltage offset errors is a beautiful thing.
    • Just get a Haltech CAN wideband, no need to wire any delay circuits, or relay, etc. Since I've moved to a Haltech CANbus wideband, I have not replaced a single sensor for over 5 years (if not longer, can't remember when moved to Haltach).
    • Small analogue delay circuit with a relay. Just need a trigger, say, fuel pump running for more than 5s or so? Or, you could go full mental and write a sketch for an Arduino.
×
×
  • Create New...