Jump to content
SAU Community

For Sale Gunmetal R32 Gtr $16,000ono

doritoboy
 Share

Recommended Posts

doritoboy Explorer

doritoboy

Posted
Posted (edited)

R32 GTR skyline, 10 Months reg, excellent condition always garaged regularly serviced, recently replaced timing belt kit, heavy duty clutch, inlet manifold gaskets, injector clean, all oils and fluids replaced, comp test. Has all new suspension with coil overs, replaced coil packs, repaired and re calibrated air flow meters, pod filters, Nismo wheels with near new tyres, Exhust 3.5 inch. Apart from that the car is standard and unmodified with stock boost. spent alot of money on the car so new owner wont have to spend anything for a long time! Need to sell to keep up with the mortgage repayments. Having said that im not open to ridiculos offers but there is the possiblility of negotiation. Located in South east Melbourne.

ph.0421848138

Image0025.jpg

Image0026.jpg

Image0031.jpg

Image0028.jpg

Image0027.jpg

Edited by doritoboy
Link to comment
https://www.sau.com.au/forums/topic/302750-for-sale-gunmetal-r32-gtr-16000ono/
Share on other sites
doritoboy Explorer

doritoboy

Posted
  • Author
Posted
What were the readings of the comp test? Any oil leaks? Gearbox noisy/crunchy? Any rust?

Thanks

comp test came up as between 150 -155 in all cylinders, gearbox shifts fine but there is a little whine in first and second gear. has a tiny bit of rust at the back of the drivers side rear wheel arch

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      This was a huge help.  We followed the steps,  although shifting into 2nd was actually into 3rd for us,  and 1st was into 2nd ( steps 9 and 11) .  The long flash was the 4th flash.  So shift solenoid A is possibly the culprit.  Is this inside the transmission itself? Or is it accessible by just front the pan? Or is it bolted to the outside of the transmission?  Thanos for your help everyone
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      Can you enlighten me on your best practice regarding these hoses? I don't wanna make the same mistake if you already got a better solution.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I have some silicon hoses already, for example engine to watercooler. But yeah, I get the sentiment. The lower intercooler silicon hose is drippy too, despite not being very old. Does anyone except Nismo make these same lines out of rubber? Long term I think they'd be the better replacement, especially since the car won't live as hard a life anymore as in the past nor be driven as often.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I know most issues are just age related. But for example the turbo oil drains, there is dash adapters for these and you can just make a braided teflon line for them and (probably) never have them leak again. Also not terribly expensive. Can you even get the factory hardlines from new? Or are they repairable if they break?
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I know it'd be much much easier with the tool. I hope I can find one that won't take 3 weeks to get to me an isn't a "Asian models kit" that has tons of (to me) useless adapters for a load of cash.   It's a summer project/fun car. I do wanna enjoy it, without endless downtime over and over. So yeah I would even go and buy an engine crane + stand to save myself the trouble of hard to reach or unreachable places going bad later on. Would also be a good opportunity to put on a Fluidamper, renew the mains seals and stuff like that. I have some money on the side that I can use for that, what I wouldn't want to or be able to do is let everything be done by a shop or have my engine completely rebuild right now. I intend to do most of the "doable" jobs myself. Pulling an engine can't be that hard, can it?
×
×
  • Create New...