Jump to content
SAU Community

Bought Some Wheels And Would Liek More Info On Them

jakez88

By jakez88,
in Exterior & Interior Styling

 Share

Recommended Posts

jakez88 Veteran

jakez88

Posted
Posted

ey guys just bought some new wheels from japanese import spares in adelaide. been watching there stock for a while and i saw some wheels come up that i really liked. anyone looking for some tuff jap wheels for cheap i suggest have a look at their stuff.

so far all i know is that they are work rs but thats all i know. tried to look for more info on them but haven't found anything plus theres something written on the centre caps but dunno what they say. can't make them out.

if anyone has seen these at all or know what they are let me know and if you have some pics of them on a car even better!

12693DSC04557.JPG

  • 1 month later...
batakr33 Rising Star

batakr33

Posted
Posted

Those are the exact wheels im after ! fcukin though dude howmuch you pay for them ? any pics of them on your car ?. If you look at the latest HPI there is a pic of a red R33 with these wheels looks amazing !

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...