Jump to content
SAU Community

R32 - Clean - Street - Drift - Track

LRyder

By LRyder,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

RaceDat Apprentice

RaceDat

Posted
Posted
wat parts do u have and are they rego?? wat area you located in

The datsun can be rego'd but will need mod plates for the cage & stuff ..... The r32 cant be..... The car is a project the motor & box are in most of the wiring is done just a few little its to be done. it has front coilovers full r33 rear end in it i have both the 32 & 33 tailshafts that need o be moded..... The Datsun is 2nd in qld in juniors never hit anything only thing that has gone wrong with it is i destroyed a diff....i am located in warwick qld 4370....Datto dose 1 20's around morgan parks 2.1km circuit and 1:08 around QR on the sprint track i beleive it is

wpn32 Collaborator

wpn32

Posted
Posted
The datsun can be rego'd but will need mod plates for the cage & stuff ..... The r32 cant be..... The car is a project the motor & box are in most of the wiring is done just a few little its to be done. it has front coilovers full r33 rear end in it i have both the 32 & 33 tailshafts that need o be moded..... The Datsun is 2nd in qld in juniors never hit anything only thing that has gone wrong with it is i destroyed a diff....i am located in warwick qld 4370....Datto dose 1 20's around morgan parks 2.1km circuit and 1:08 around QR on the sprint track i beleive it is

im located in melb, qld is too far and need something with reg as my r32 is my every day car

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      ugently need expert / experienced opinion

      By GTSBoy 路 Posted

      There's more than one way to skin that cat, and most of the sump Maatouks have done will be GTR sumps. They are HUGE in GTR drag racing here.
    • dbm7
      Shifting questions

      By dbm7 路 Posted

      Yeah...I always start at the shift solenoids, because there's only a few reasons these will spook into limp mode, and bad shift solenoids is one ~ the other can be the shift control module (if you have steering wheel shift buttons)...it's easier to eliminate the solenoids first.
    • cabramatta
      Never ending fuel pump drama

      By cabramatta 路 Posted

      Might piggy back off this thread since there's been a good discussion about PWM.   I purchased a Walbro 460 F90000267 and have been looking into PWM to understand it. It was purchased more of a future proof as my original OEM fuel pump died (r33 below 200kw) and figured I'd just upgrade it to this. That's when it hit me that a pump this big can cause more dramas with such high amperage draw and heating of the fuel pump being on 100% all the time in such a mild setup.   I have a Nexus R3 and slowly collecting power mods but I was looking into the PWM feature on the NSP software:   Then looking at the graph from the fuel pump:     Am I safe to assume reducing duty cycle to 50% for example would make the pump run like a 230/lph ? Where does the PWM come in all of this ?   I've gone down the rabbit hole of PWM fuel pumps and it seems there are many differing opinions on how to go about it 馃槄  
    • DRoc81
      Shifting questions

      By DRoc81 路 Posted

      Thank you, this will keep me busy for a bit.  I will update progression.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 路 Posted

      That specific one would be an exchange part, meaning I'd have to send mine to them. Plus it looks like a non AWD sump, which won't work for me. There is one or two shops in my country that I can ask to do a sump extension job and it'd most likely end up being cheaper than sending mine to AUS or NZ and getting one back, and quicker too.
脳
脳
  • Create New...