Jump to content
SAU Community

Recommended Posts

Rb20 ECU $120

Nistune chip with transplanted rb25det maps around $220 i think.

Few $100 for quick tidy up fine tuning

double that.

http://www.nistune.com/boards.htm

DRDRIFT is good at his job and that price is very fair, i wont do it for less than 1k

Im getting the z32 ecu with nistune installed and tuned for $900. I think the only advantage of the z32 is that it retains the vct. I would say 700-800 is a pretty good price. Make sure to shop around though because i got quoted $2000 at one place i rang, i choked on the phone when he said that.

Im getting the z32 ecu with nistune installed and tuned for $900. I think the only advantage of the z32 is that it retains the vct. I would say 700-800 is a pretty good price. Make sure to shop around though because i got quoted $2000 at one place i rang, i choked on the phone when he said that.

haha @ 2k that buys alot of stand alone ecu's, i feel bad charging 1k, but it aint worth my time touching it for any less.

double that.

http://www.nistune.com/boards.htm

DRDRIFT is good at his job and that price is very fair, i wont do it for less than 1k

420 if you want the software so 220 is correct for just the chip i know because it's the price i paid i also installed the chip myself

Edited by Crans
420 if you want the software so 220 is correct for just the chip i know because it's the price i paid i also installed the chip myself

still double as no-ones gonna bother tuning it for a couple of hundred, was my point.

or you could just buy an off the shelf powerfc for $1k and use that?

when your finished, sell it for the $1k you brought it for, no money lost

still gonna cost you another 500 (so 1500) to get tuned at most decent shops... i prefer the PFC in 33's to though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...