Jump to content
SAU Community

Light Throttle Issues.

Shaun O

By Shaun O,
in Engines & Forced Induction

 Share

Recommended Posts

Shaun O Enthusiast

Shaun O

Posted
Posted

Annoying problem that's crept itself up, on very very light throttle, the engine stutters a little, like, super light throttle (1k-1.5k~ or so RPM while in neutral) - it's not the throttle cable either because it does it when you manually give it throttle off the throttle body.

Any ideas?

Giving it a tad more throttle and it's no problems. It just makes the ride really jerky sometimes when driving in like 2nd gear at low throttle. It's an RB25DET throttle body (S2)

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/304572-light-throttle-issues/
Share on other sites
Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted
Sounds like its running lean there, possibly due to the airflow meter being dirty. Give it a clean first with a can of CRC airflow meter cleaner and see if that fixes the issue first.

Cheers, I don't have any CRC AFM cleaner, will something like Isopropyl Alcohol work?

260tech Proficient

260tech

Posted
Posted

Yup, isoprophyl alc is good, absorbs water & leaves no residue, also check plugs for gaps, & coilpacks for moisture & crap that will make things (sparks) track. give the coilpaks a wash with the iso & spray with a silicon inhibitor. Quote gospel from PI #116

Cheers GW

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted
are you using an aftermarket ECU?

add some more accel enrichment and see how you go

Nah, just a standard chipped ECU, it hasn't always been an issue and just seems to be intermittent, it barely did it at all on the way to work this morning. I'm still at work though so haven't tried the cleaning stuff yet.

FULL RABBIT OR NO RABBIT!!!!!! noone likes a tortoise, light throttle is for wimps.

Haha, unfortunately that doesn't work so well in peak traffic :(

Plus, I wish my car had a lawnmower style throttle instead of an accelerator pedal :P:D

NZM.031 Grand Master

NZM.031

Posted
Posted

ok so you want it fixed then.

afm or sticky butterfly would be a good place to start... get out with some carby cleaner.

slight vacuum leak.

dodgy injector, may be spraying to much or dribbling out and flooding one cylinder or not spraying enough due to blockage and running lean in one cylinder.

dodgy plug, same as dodgy injector but different.

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted

Well I just sprayed the AFM and all the coilpacks with iso alc - left it for a bit to dry then fired her up, it was doing the up n down up n down up n down revs at low throttle still but only for like 10 secs, from then on it seemed all good.

I didn't have any long sockets for the spark plugs but will find some if it happens again over the next few days.

Cheers guys.

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted

Changed the spark plugs, no difference - thought I wanted to change them anyway :) (and only $20NZD for the set, can't go wrong)

Until on my way home, hit a little boost and FSHHHHH, the silicone joiner between the turbo and the intercooler piping blows off.

I have a feeling this has been the problem all along, leaking out of top of this joiner.

Gotta try my best to get it on real good tomorrow morning, will post back results.

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted
good work man... that will do it. hope its all good.

Yeah cheers, I tried my best but I think my hose clamps are being shit as well as the 90 degree silicone bend.

Getting a 90 degree stainless welded onto the end of the intercooler piping to eliminate the 90 degree silicone bend and put a straight silicone joiner between the turbo and IC piping instead.

Actually works out to be similar price in the end anyway, just a little more hassle but becomes better off in the long run.

Going to get a new hose clamp as well to replace the one that I think is no good.

Will post back results tomorrow night ;)

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted

Just f**ked around with hose clamps and shit just to see if I can have it running a bit nicer for tomorrows driving.

Started the car up, idling like f**kin' shit, hunting up and down, getting worse and worse and then stalling.

'f**k this' I think to myself, get in the car and just go for a wicked thrash.

Park back up again, idling like a f**kin' dream and not being gay on low throttle, WTF!

So see what happens tomorrow morning on the way to work! - Still going to replace the silicone 90 degree with stainless steel though.

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted
What AFM are you running? It might have the dreaded bad solder joints on the board inside.

It's an RB25DET S2 AFM, I have a 300ZX AFM here ready to go in whenever I can get the car tuned/chipped.

Is it something that I can fix myself? Or if I open it up will it be easily spotted?

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • MBS206
      R32 GTST - 600KW+ RB28/CD009 Build

      By MBS206 · Posted

      Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • dbm7
      Stagea Front CV Axle Question

      By dbm7 · Posted

      Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • Duncan
      Stagea Front CV Axle Question

      By Duncan · Posted

      I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
×
×
  • Create New...