Jump to content
SAU Community

Recommended Posts

I am a soldier in the US Army and i have been stationed in landstuhl, germany. I bought a 1994 Skyline GTS-T Impul edition sedan from an older local german. The problem the car is having is when the revs reach 4700rpm under acceration (autobahn ) the car feels like it hits a wall, like rev limiter, but if i ease off and accerate slowly with no boost it will break through the 4700 rpm mark just fine.

It seems to me the only time it hits that wall is under moderate acceleration when boost is up. The things on my list to do are ngk plugs, fuel filter, and spaying the mass air flow meter with some brake cleaner. I've ran a tank of fuel with stp fuel injecter cleaner through it since i knew it had been sitting for 6 months but what else should i do? How can i accerlate moderately without hitting that wall at 4700 rpm?

Link to comment
https://www.sau.com.au/forums/topic/305358-severe-stutter-at-4700rpm/
Share on other sites

What boost is it running?

If u keep your foot down does it seem like it gets back power at about 6000rpm?

full stock,about 5 psi the only aftermarket is a downpipe back jasma exhaust and a tune job RAZO(who knows)

After 4700 rpm anything more than a granny foot the car starts stuttering

Edited by Impul-R33
OK if its only 5psi it shouldn't be "rich and retard"

Stock ecu i presume?

U can check all those u listed above and try and get some good fuel in it and reset the ecu

the ecu, i have no idea, it was originally tweaked by impul, then tweaked again by a german tuning company called RAZO, right now its running 105 US octane rating

all gears,but not in neutral, it would make sense it being the fuel filter or fuel pump, its been sitting for a while, my manuel is in japanese so maybe you can help me out on this one, Where is the fuel filter? the only one i ever replaced was in the tank and i could gain access to it thru the trunk, I'm guessing its an inline filter under the hood to the left of the intake manifold but i cant tell, it could also be a regulator of some sort.

Edited by Impul-R33
all gears,but not in neutral, it would make sense it being the fuel filter or fuel pump, its been sitting for a while, my manuel is in japanese so maybe you can help me out on this one, Where is the fuel filter? the only one i ever replaced was in the tank and i could gain access to it thru the trunk, I'm guessing its an inline filter under the hood to the left of the intake manifold but i cant tell, it could also be a regulator of some sort.

Follow the fuel lines back from the fuel rail. The filter should be in the engine bay.

Dunno what side drive you have but it should still be on the intake side regardless.

It's small like a can of beans

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. So I have my GTR on the lift and have been working on it a few days and today I unpacked the frontpipe that was wrapped with heat wrap stuff, because part of it was breaking down and soaked in oil. Noticed that the pipe itself does not actually look like a Mines, despite it supposedly being a Mines. But I could not find any fronpipe online that looks exacly like his, and I don't think it is a custom one. My amateur measurement also showed the two pipes are about equal length, so maybe this is just an old version of the Mines pipe? Would appreciate insight on this by the enlightened folks. greetings from Germany
    • Yeah. If I plug the connector in and connect the vacuum lines, I assume worse case scenario is that it simply doesn't work? Yep PFC.
    • I would think that rather than attempting to perform an engine swap, with all the difficulties associated with doing so in a country where the raw materials required are harder to get hold of, I would just build the CA20 for boost, find an EFI manifold for it and either add a turbo or a supercharger. Or both. You replace one set of difficulties with a different set, but I know which would be more fun.
    • Well, a proper aftermarket ECU** SHOULD be set up to run the purge solenoid, same as the factory ECU would, so that the tank breather system continues to operate the way it is supposed to. I have no knowledge of whether the PFC (which is what I assume you mean when you say Apexi) has an output (and internal logic) to run the purge solenoid. If it does not, then given the product design intent for the PFC, which is to be a plug in replacement for the stock ECU, I would consider that a massive failing on Apexi's behalf and would be another reason to think that they were a half-arsed solution to the problem if programmable management on RBs. I would suggest that since Nistune came to market (which is a LOOOOONG time ago now) there has been no valid argument for choosing a PFC, especially if the PFC can't do things like this.   **ie, Haltach, Link, Motec, etc
    • Thanks for asking the question we were all thinking!
×
×
  • Create New...