Jump to content
SAU Community

Quality Tuners Nor?

rinart

By rinart,
in Western Australia

 Share

Recommended Posts

rinart Apprentice

rinart

Posted
Posted

Hey all have a basic rb20 set up with 25 turbo,fmic,full 3inch exhaust.

Im looking for a good tuner north of the river that knows there way around rb's to fit an aftermarket

computer (or what ever my other options are) and tune it but i dont really know what works best.

If it makes any difference to which ecu to select I can see myself installing bigger hp injectors,turbo and afm in the near future.

Im pretty much wanting to find out the following -

A proven tuner NOR.

What ecu setup to run

How much am I looking at for ecu + tune.

Cheers guys

Link to comment
https://www.sau.com.au/forums/topic/305810-quality-tuners-nor/
Share on other sites
dan_the_man Grand Master

dan_the_man

Posted
Posted

Thread closed. Believe it or not, but since SAU started more than 7 years ago, this topic has been discussed before.

Please use the search function in future. It may be found here:

http://www.skylinesaustralia.com/forums/search.html

While we understand that it can be frustrating to have your thread closed - Please consider that other members may feel it to be disrespectful and selfish of you to post a simple question, without using the search feature to review the wealth of information provided by said members over the years.

If you still feel that this action is unjust, then please PM me and we can discuss it further.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Everything I found online said never use it because it'll dramatically reduce belt lifespan.  No, but I have seen excessive v-belt tension cause the audible bearing noise from excessive radial load in things like alternators. So don't overdo it. Ideally you set it to manufacturer spec using a proper belt tension guage. I tried the "clicker" type gauges but those cheap things are trash. They read way too low even when you're careful.
    • joshuaho96
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By joshuaho96 · Posted

      This is kind of where I've ended up for the most part. It's easier for me, easier for shops that don't have to deal with my weird criteria/picky standards, etc.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      Will do. Suprised if it's not the starter motor considering it's 30 years old. Will get a volt meter though. Battery is close to new.   Cheers for your help, always appreciated.
    • GTSBoy
      Rb25det Belts Change

      By GTSBoy · Posted

      This almost never happens these days. No. Clean your battery terminals and make sure they are tight. Use sandpaper on a dowel if you have to, to get oxidation off the inside of the terminals, particularly on the -ve. Check the earth cable from battery post to chassis ground and engine ground. Make sure the contact surfaces are clean - including the threads on the bolts that anchor them - because that's where a lot of the contact occurs. Wire wheel on a drill is a good thing for this. Make sure the crimps on those cables are all sound. Assuming none of that causes an improvement: Check the battery voltage after it has been resting for a while. If it's at the lower end of the range, put it on charge for a while, then see if it will crank better.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      I just checked my belt, it wasn't super loose but I could bend it past 90 degrees a small amount so I tightened it up and for the first time ever my car didn't crank first time, had to crank it again lol. Don't know if that was because I tightened the belt or if it's my starter motor going out (been having slow starts for some time). Coulda also been when I was recording I didn't crank the key properly and it didn't save the recording lol.   Is that a thing if you overtighten a belt it struggles to start?
×
×
  • Create New...