Jump to content
SAU Community

Double Sided Stickey

66yostagea

By 66yostagea,
in Four Door Family & Wagoneers

 Share

Recommended Posts

66yostagea Grand Master

66yostagea

Posted
Posted (edited)

On the horizontal section or my rear bar is a plastic emblem with the word Stagea in styleised form. When the bar was replaced I took the emblem off. It was stuck down with a thin DST. I have tried various tapes without success. It starts to lift then cant open the tailgate. Anyone know of a good tape to get and where.

Edited by 66yostagea
Link to comment
Share on other sites
Appealing Proficient

Appealing

Posted
Posted

Hi Hugh

Try a sailmaker, most sails today are held together with DS tape before sewing.

Tell them you want a high tack one (not starboard or port tack.... joke!). If you want one with foam as well, then try a specialist distributor.

We have Heatley Sales over here, they have just about every type of tape known. Alternatively try Spandex (a company not a pair of tights!). They are a specialist sign supply company.

If you want to wait a week or so, I'll send you some over. Cos if you buy from the above (other than the sailmaker) you might need to buy a roll..... Thinking about it, I am right down, so I'll send you the end of the last roll. PM me your address.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • OST Micah
      RH9 R32 GTR Build Thread

      By OST Micah · Posted

      A year of slogging through this bearing issue and finally fixed. What a nightmare. The oil pressure increase did not fix the problem. If you would like to read all the details in case you ever run into a similar issue visit my thread on Yellow Bullet. https://www.yellowbullet.com/threads/continuous-rod-bearing-issues.2689569/?post_id=74193031&nested_view=1&sortby=oldest#post-74193031 In the end the rod bearings themselves were the issue. I had switched from ACL (first engine) to King because that was all we could get at the time and I thought nothing of it. Put the ACL's back in after a year of taking the pan off multiple times to change many things. Issue resolved. Can't believe it was just the bearings themselves all along. It has now been about two years since I drove the car on the street or had it at the track. At some point I had installed all solid and spherical bushings in the rear but had never aligned it since it just went on and off the dyno. Alignment was the first thing to do. (Old photo but same concept) Then I took the transmission out and went through it. This was my first gearset install and I've done about 15 since this one and learned a lot and wanted to apply some of these tweaks to mine. The aftermarket shift forks take very well to some modification and I wanted to make that change. Shifts are now super smooth and no having to find the gear. I also recut the 5th and reverse shift sleeves - always wanted to try this and see how well it works. It works very well! No grinds or having to do a second attempt going into reverse and 5th is perfect. Before During After Going back in In rummaging through my spare trans parts box I found the only parts I've ever broke on a stock trans; the 3-4 shift fork - twice!  
    • Kinkstaah
      R32 Gtr Long Term Love, Now Project

      By Kinkstaah · Posted

      It also depends on gearbox ratio. Those drag cars running 7s passes aren't doing it on an overdrive gear ratio (probably). 1:1 is "fine", the critical RPM for a 50' single driveshaft in chromemoly is 6900rpm.... ....but when you shift into 5th and use 0:73 or 0:8 it all changes. Do you know their rear diff ratio? etc. That's the stuff that matters with regards to it. Whether it actually matters given your use application is also relevent. You may never get into those scenarios, like most ruined GTR's from Western Sydney don't :p
    • Dose Pipe Sutututu
      R32 Gtr Long Term Love, Now Project

      By Dose Pipe Sutututu · Posted

      but for how long? would it handle a few laps around SMSP in anger? 
    • GTSBoy
      R32 Gtr Long Term Love, Now Project

      By GTSBoy · Posted

      And over it. Need to stop it coming through the floor.
    • Duncan
      RB30 Struggles from idle

      By Duncan · Posted

      Is it running the standard ECU? some sort of data log might help understand where timing, AFRs etc are at.  If it is standard ECU something like Nissan Datascan would help
×
×
  • Create New...