Jump to content
SAU Community

Recommended Posts

Well its been ages since i actually contributed some useful shite around here, and lately i have been amateurishly testing the various fuels currently available to the common joe with an import.

I have been using (and car tuned on) BP Ultimate 98 octane fuel, which is widely renown as a reliable fuel, hence is popularity.

Tried Caltex's new 98 octane a couple weeks ago, no complaints, didnt see any knock over 20 and didnt experience any difference in driveability.

Same goes with United 100 octane, chucked it in an empty tank tonight and didnt see any knock over 20, granted i did only drive around 10k's on it.

I dont give a fat rats what studies show, this thread is for those people who have tested a certain fuel in their car and are happy with it (their own physical experience with it), or are unhappy with a certain fuel (bearing some consistency in mind, dont whinge if you've had one bad tank in 3 years from the one servo). One day we may have enough competition between the various 98+ octane fuels to see some price competition, which will only benefit us!

This can also include those using ethanol based fuels, maybe you have been experiencing a different result with different suppliers, etc. or first hand opinions of power vs cost vs economy..

Commence.

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/
Share on other sites

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

i used Shell VPower with no hicupps

i used the premium 98 @ the united on grange rd towards hindmarsh end and pinged hard straight away but i reckon from that site there 98 isnt a high seller so was probably old fuel or had high concentrate of water in it

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065840
Share on other sites

I use the BP 98, the Mobil 98 and the Caltex 98. Have used vpower before, no complaints. I've ran the mobil 98 for the longest amount of time, however since caltex took mobil over, theyve been offering the same fuel, so I go to either now. Never had issues with fuel on my tune.

-D

i used united, shell, bp and they all seem the same..

im about to try united E85, but have been told to go to scotchers?

reasons y and is it worth the .70c?

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065866
Share on other sites

I use 95 Caltex, and 95 BP.

I would like to use Shell V Power at some stage, but I prefer the BP.

United 95, i did notice slightly less fuel economy also, within 50kms of BP 95.

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065884
Share on other sites

iam a big fan of e85 united is fine and never had any probs with it lots of blokes use it round adelaide and it has seemed to be a safe place to get it from mind u its only a new thing at the united on tapps hill rd.

at 99cp/ltr the added horsepower is unbelieveable even on mix or straight fill but this fuel will only have the benifits reaped once tuned and will consume it 30%faster but not all bad with an extra 7 degrees of timing and self oxygernising(spelling sorry) the boost can be stuffed in hard and fast.and just quietly the smell of e85 in the morning is just horn hahahaha.

love it or hate it i reckn its the ducks guts and so far proven to me to be one bloody great way of extracting power N/A, charged or blown and for any of u blokes worried about pinging fill up with 98 and chuck 3-5 ltrs in a full tank to keep the octaine rating up (un-tuned)

now scotchers is only more expensive due to buyer power thats it the united gets a fair regular test from a particular tuner down south so if its good enough for him iam keithy by it! go get some boys oh and a new tune hahahhaaha

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065891
Share on other sites

The cars that are designed to run on E85 are Multi fuel vehicles. They have a sensor in the tank and can run everything from E0 to E100?. They do this by having flexible maps that adjust to the fuel that is in the tank. we don't have flexible maps; we have a fixed tune that creates problems if the properties of the fuel change from what we had in the tank when we got it tuned.

The service stations don't guarantee the ethanol content and they definitely don't guarantee the octane rating (not that the fuel is rated by octane rating), Jeff mentioned that from what he has seen with the E85 tunes there is a definitely a consistency problem in that if a car returns to the dyno he has to change the tunes because the fuel properties have changed from tank to tank.

The scotchers E85 though is guaranteed to be the same every tank, after all it's what the V8 touring cars are running and they need consistency.

It's up to you what you run, at the end of the day it's your engine; but fuel isn't the thing to cheap out on.

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065910
Share on other sites

thats a fair call i didnt realise this about ur cars. do u blokes have the option or ability to have designated tunes for these types of fuels?

so would this mean p100 would mess with ur tune as it is now?

are all skylines set to one specific fuel grade? as u mentioned what grade is this?

i was under a general assumption that the ability of ur comp systems would still be able to vary knock,temp,octaine to a degree of some sort even if its a little, due to typical variances on an everyday scale?

i know e85 is a big f*kker to the fuel system ie old rubber hoses an such it just corrodes them apart but the newer style rubber joiners and hoses are fine with this type of fuel

please dont think iam being a jack ass just intrested to learn

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065936
Share on other sites

The skylines have knockmaps but they are more for saving the engine so they generally are very rich and retarded (i.e. gutless). If your running Power FC you don't have any knock control, you just get a flashing light on the dash if you get a knock event. you do get a knock value on you hand controller as well.

From what i understand about the flash tunes your tunes are specific to a certain fuel. You do have knock maps but they aren't the same as what the multifuel vehicles run; They run an infinite amount of maps for every fuel grade.

EDIT!!

Have a read of this, it's for an aftermarket gauge to let you know your ethanol content but it gives some background into multifuel vehicles.

http://www.zeitronix.com/Products/ECA/ECA.htm

Edited by D_Stirls
Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065952
Share on other sites

yes this is true each tune the flasher can hold 4 at any one time is specific to each octain/tune type so in my flasher i have the ability to have my e85 tune then a 98 then a 95 and even a custom tune to not go over 3000rpm if i want the tuning capiabilities of the flasher are very good, so i take it the power fc can only hold 1 custom tune at any one time?

so yes this would make running e85 a bitch due to avaliability

any aftermarket ecu that can have more than one tune switchable in it for u blokes?

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065963
Share on other sites

Just have your laptop handy and you can have 100's of tunes. With Power-FC you will need FC-Logit which will cost you around another $450 but once you have that you can do anything.

I run this; Which allow the same switching of maps and you retain the factory ECU so you retain the knock control that you lose with P-FC. The only thing that it doesn't have compared to P-FC is 20x20 map resolution, it retains the factory 16x16 resolution.

http://www.nistune.com

It's only $440 including the chipset and the tuning software.

You'd still have a problem if you get a sub grade batch of E85 wouldn't you as you physically have to switch the tunes don;t you it's not automatic.

Edited by D_Stirls
Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5065977
Share on other sites

yes this is true each tune the flasher can hold 4 at any one time is specific to each octain/tune type so in my flasher i have the ability to have my e85 tune then a 98 then a 95 and even a custom tune to not go over 3000rpm if i want the tuning capiabilities of the flasher are very good, so i take it the power fc can only hold 1 custom tune at any one time?

so yes this would make running e85 a bitch due to avaliability

any aftermarket ecu that can have more than one tune switchable in it for u blokes?

whilst the PFC is rigid in its maps we can buy external software to save extra maps and load on with a laptop 1 aforementioned programs is datalogit

http://www.fc-datalogit.co.nz/

there are also jap variants of the same

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5066033
Share on other sites

Or you can get nisstune for $200 and the daughterboard for the $250 mark. Real time tuning, regency friendly.

-D

whilst the PFC is rigid in its maps we can buy external software to save extra maps and load on with a laptop 1 aforementioned programs is datalogit

http://www.fc-datalogit.co.nz/

there are also jap variants of the same

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5066036
Share on other sites

a good friend of mine used to organise all the trucks to do the fuel deliveries to a few different companys petrol stations. apparently mobil import the fuel and then on sell to bp and shell. this is ready to go fuel ill also mention, so presumably there is no different between 98 octane bp shell or mobil.

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5066283
Share on other sites

I've tuned most 98's to the det threshold, Ultimate and Mobil 8000 were the only ones I trusted!

I dont think scotchers is sourcing his E85 from the same place as the V8's, they have an exclusive contract with CSR, at a guess he would be buying it from the same wholesale market that united get it!

the only difference is he orders it in a "98" blend, which IMO makes bugger all difference, I've tuned and used united E85 for months now and find it comes up just as good as the "98" blends I was buying from racefuels in victoria.

Link to comment
https://www.sau.com.au/forums/topic/306439-fuel-and-you/#findComment-5066359
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Hope the cans went down well at least 
    • 255 can't go wrong with the price.
    • When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
×
×
  • Create New...