Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Help me get my shed back in order. Need to fund a new wakeboard!

HKS VPC. Come with everything. Use this to remove your AFM's on your gtr and still run std or pfc ecu $400

Set of front guard liners and front under tray. Has front brake ducts and I won't seperate. $250 Getting very rare!

RB26DETT oil pump $80

Harmonic balancer $50

R32 GTR fuel pump in cradle $80 each. I have two of these.

Twin Turbo pipe - From turbo's to intercooler pipe $100

R32 3inch exhaust with seperate de-cat pipe. Has centre muffler, no rear muffler, just straight throught to out back $100

Standard R32gtst exhaust I used to clear epa on gtr $100

R32 GTR metal fuel cap $30

R32 GTR ABS mater cylinder $100

R32 GTR G-Sensors $100 Qty 2

All ECU's below suit std injectors and turbos

2x Mines ECU's for R32 GTR $100 each

Blitz ECU for R32 GTR $100

New R/H sill panel $100 Suit GTR/GTST

R/H tail light $30

R/H mirror $25

R33 GTR lowered rear springs for std style shocks $50 sits very nice

Tein stiff springs. Perfect for drift. $30

Melbourne Can post. Please no time wasters. You know who you are!

This will all end up on ebay if its still around in a few weeks so I thought I'd give the SAU crew first dibs.

Looking for a std boost solenoid, flywheel and clutch and intercooler for R32 GTR.

gday there buddy , how are ya , just wandering if you would have a clutch vacuumm master cylinder lying around in great condition also a stock r32 gt - r , plastic front bar , in stock ready to go

let me know asap hey , much help appreciated

cheers anf

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
    • How does this compare to the internally gated g25-550 in terms of power production at same psi and spool
    • Did you find that your voltage of the battery wasn't where it's normally supposed to be? for example on my r34, it's at 14.5v when running after a few seconds, but I noticed when I had a rough start and it initially wasn't idling correctly, the voltage on my triple gauge cluster was showing lower than usual. Seems like the alternator is starting to crap itself
×
×
  • Create New...