Jump to content
SAU Community

Recommended Posts

If I could borrow anyone's Greddy Profec B spec II controller, just need to conect it up take the car for a spin to see if my controller is stuffed. Have already changed the solenoid with no luck. Checked the continuity of solenoid control loom, all good.

Please let me know if you can help.

Located near Tea Tree Plaza.

Cheers,

Kym

Link to comment
https://www.sau.com.au/forums/topic/307581-any-one-got-profec-b-spec-ii/
Share on other sites

  boosted_sa said:
If I could borrow anyone's Greddy Profec B spec II controller, just need to conect it up take the car for a spin to see if my controller is stuffed. Have already changed the solenoid with no luck. Checked the continuity of solenoid control loom, all good.

Please let me know if you can help.

Located near Tea Tree Plaza.

Cheers,

Kym

hey mate,

what exactly is it doing/not doing?

  mlr said:
I burnt through my vacuum lines at my wastegate and it did that, hows your lines ?

i highly doubt the controller is faulty. check your in-line filter, as well as all your lines. What does your boost gauge idle at?

  boosted_sa said:
How would I hook the solenoid up to the Power FC?

as far as i am aware, you cannot. Apexi make a PFC boost controller, but it is $400-$700 extra!

there should be an inline filter between the pressure source and the controller unit, otherwise any crap can daamge the pressor sensor inside the unit.

Also, might be worth checking for a vacuum leak, because as Krishy said, it should read -99 at idle.

all else fails, do a reset (RTFM), and go see a tuner.

  BIT SUS said:
as far as i am aware, you cannot. Apexi make a PFC boost controller, but it is $400-$700 extra!

there should be an inline filter between the pressure source and the controller unit, otherwise any crap can daamge the pressor sensor inside the unit.

Also, might be worth checking for a vacuum leak, because as Krishy said, it should read -99 at idle.

all else fails, do a reset (RTFM), and go see a tuner.

yep spot on nigel.....you cannot hook up a greddy product to an apexi product and make it work lol.....well havent seen one so far

as nigel said check all your vacuum lines...replace them if you have to....and google up some settings....if worst case scenario then take it to a mechanic and get it looked at/tunned

i would just keep the 2 separately mate....the profec will do its job and the pfc will do its job lol....

well hopefully whatever problem you have had gets sorted out soon....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...