Jump to content
SAU Community

Recommended Posts

Both modules are for the fuel pump they need to stay

Cheers Ryan.

Going to go all custom wiring. Fuel pump was already earthed out to run permanent 12V once the ECU told the pump to turn on. Will put a decent new relay on it, and all new wiring.

From what I understand those things are only useful when running the funky ECU speed controlled stuff.

Doesnt the two stage pump thingie stop the fuel from getting to hot by slowing the flow at a certain RPM, colder fuel helps cool the cylinder?? I think???

Mine pumps more from 2k if my ear is calibrated with my brain, but then thats a big ask.

Doesnt the two stage pump thingie stop the fuel from getting to hot by slowing the flow at a certain RPM, colder fuel helps cool the cylinder?? I think???

Mine pumps more from 2k if my ear is calibrated with my brain, but then thats a big ask.

Yeah, that's what it's designed to do. Mainly to stop cars in traffic from over heating the fuel.

Car is track only, so it's going to spend most of it's time >3000RPM anyway, so fuel pump will always be cranked up.

Along with all of that, this was on the drivers side, just under the back window... I believe it is the high speed fuel pump relay? Can someone confirm?

387558_2582321391859_1069171597_32764556_239746913_n.jpg

Also, this box sits bolted to the inside of the rear guard beside the aerial unit... Is it apart of the aerial stuff or for some other lighting?

403763_2582323511912_1069171597_32764558_1021430298_n.jpg

Matt,,,both can go,,,don't ask me how to rid yourself of the fuel pump one but mines in the junk box.

Cheers

Neil.

If you are not running the factory ecu and engine you can get rid of them just make sure the pump/s are wired up to meet the cams regulations.

Neil do you still run the key for the ignition? I think the rule is if the engine stalls and the ignition is on the fuel pump must shut off, not 100% but worth a look.

Good luck

If you are not running the factory ecu and engine you can get rid of them just make sure the pump/s are wired up to meet the cams regulations.

Neil do you still run the key for the ignition? I think the rule is if the engine stalls and the ignition is on the fuel pump must shut off, not 100% but worth a look.

Good luck

Yeah the ECU is going to be setup to switch the fuel pump. Pretty much like normal, once the ECU loses an RPM signal it'll kill the pump.

When first turning it on, make it prime for 3 seconds.

fuel one is easy, you just jumper the 2 earth pins on the plug to that unit under the parcel tray and its on 100% full voltage

That still leaves wires that add a small amount of weight... :P

The wiring is gone now too... LOL... Custom relay and cabling time... :D

the box under the window cant be fuel pump related. the original speak wires run thru it, and ive left it unplugged once while i had the shelf out and made no difference to the car...just the already poor stereo sound.

the other box, no idea.

  • 6 months later...
  • 4 weeks later...

lol cam. only 1. how quaint.

What is the plan for the starter motor Matt....stuffed if I can see how it will fit?

who needs a starter motor when your mates can push, LOL.

Right now... My wallet thinks this is the answer...

13149218846191971929401.jpeg

The even funnier part? I really do have these stickers for the car already... LOL

I'm about to order a starter motor relocator, just waiting for pay day.

edit: and yes, the car sat at my mothers for nearly a year (So much for 6 weeks Mum!)

  • 2 months later...
  • 1 month later...

I did try to pm ya, but wont let me.

hey matt,

I want to ask why you chosse the gen3 ls1 of all the LS series engines?

There are quite a few in the range.

They are solid engine, as i've owned 1 before.

I really wanted to say, avoid 2nd hand gen 3 ls1's from VT SS series 2 and VX SS series 1 ( unless your rebuilding) as they had a problem termed 'piston slap'. Basically holden just through in these engines that were spec'd to american conditions so the bore to piston tolerances were quite big, to deal with the extreme change in hot and cold temp's they have, so they used excessive amounts of oil and the piston would slap against the block, ultimately killing engines. With my VX SS series 1, holden had to replace the engine at about 35000km's with a revised ls1 that continued in the VX series 2 and beyond

Also when you dump the ls1 into your 33, can the car continue to be 4wd or just rwd?

Edited by badben
  • 1 month later...

nearly all of the piston slapping LS1's have been replaced by now..

He's probably using an LS1 because an LS2 / L76/98 is 2-2.5 times dearer second hand (think 2-3k vs 5-7), and about 3-4k dearer new. You can still get good power out of even the 853 (small port VT) headed LS1's, cam selection is important, and heads can be sourced relatively cheap from the US. Keen to see some more on this project btw, I'm a big fan of LS swaps into anything Jap :)

Would be keeping in mind PTV clearance if going for big lift on the cam, IMO keep the lift sane and shave the heads to get a bit more comp into it. Would recommend the Comp LSr 269 cam for your build (got one for my L76!) decent lift, nice quick ramp rates to make good power under the curve, and will make bulk torque. Have driven a WH with the Crow equivalent (or thereabouts) and was seriously impressed, given how doughy down low stock LS1s seem to be.

EDIT: Haven't read the entire thread, but are you going to stick with a JDM exhaust (will need a single 3.5 at least depending on power) Get 1 7/8 headers made up if you can, its been tested and proven that you only gain top end and dont lose any down low vs smaller primaries. Curious as to how that side of the swap works out.

Edited by bozodos

Boz, unfortunately this one has been buried at the moment (Literally, you can't really get to it at all :( ). There are plans to resurrect it in the next few months, but I have another project sitting beside it I need to finish off first.

As for the exhaust, at the moment it's looking like modified standard HSV manifolds, although that may change depending on what happens clearance wise when I raise the engine a bit to get the starter motor to clear the steering rack mount.

Edit: I think I PM'd BadBen, but yes, the LS1 was purely a cost reasoning, and they still make enough power.

With it completely stripped out how it is, it's an EXTREMELY light R33, putting more and more torque into it is just going to result in massive power skids. 5.7L will be plenty big enough with a full exhaust + cam + tune.

As for the exhaust, depending on how loud it ends up at full noise, 30 metres from the side of the track, will depend on whether I leave it as a straight through dual 2.5" or whether I have to put a muffler on each.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Also had a look at the Nissan JP website looks like the 400r has a slightly shorter ratio than than the regular V37 3.133 VS 2.937 which from a guy who has driven both 3.69 vs 4.11 ratios in the S15 is bugger all. Seems that the AUTO Z runs the same ratio as the 400R but can't find any info as to if its an open or LSD? More often than not the auto LSD is open
    • Do not replace the power steering lines with this stuff. If it's anything like the Chase Bays stuff it will leak and be worse than stock. The reason why the reservoir is on the LH/passenger side of the car is because that's just where the reservoir was most convenient to fit. Don't overthink this stuff. The intake/cold side of the engine is pretty busy on these cars. And again, the hardpipe is designed to be a janky power steering cooler. In theory you can replace it with a real power steering cooler but that's really only for track use where boiling the fluid is a distinct possibility. Start with the low pressure lines feeding the pump from the reservoir. Make sure there isn't a bunch of junk in the reservoir filter. Be careful to not get ATF all over the engine bay. I hate dealing with ATF spills, you can clean it up and the slightest crevice will still release more oil that can still drip over time. You also want to inspect for leaks before you make a mess and can't tell what happened. Most likely you have a leak somewhere that is allowing fluid out and air in. Failing that it's allowing air in but not fluid out. Only place I can really see that happening is on the low pressure side because the pump will pull a slight vacuum to draw fluid in. Everything after the pump is high pressure or lower pressure, approaching atmospheric by the time it returns to the reservoir.
    • I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
    • Do you have an IAT sensor? It's worth checking it to see. You may be suprised how little gap you actually need to flood your engine with hot air. (I tape up my airbox for a reason) :p
×
×
  • Create New...